Before Use; Safety Instructions - JB Systems Light LED WALL DIMMER Manual De Instrucciones

ENGLISH
OPERATION MANUAL
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read these
operating instructions very carefully.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
 Compact RGB remote control for LED projectors
 Extremely user-friendly and easy
 2 user programmable scenes.
 Sends 4 standard DMX-channels: R + G + B + master dimmer
 Easy wall mounting, fits in any standard recessed wall box
 Perfect for use in LED installations for hotels, homes, shops, ...
 Several wall dimmers can be combined together in bigger installations
 Comes with 2 different cover plates
 3 different working modes for maximum flexibility.

BEFORE USE

Check the contents:
Check that the carton contains the following items:
 Wall dimmer
 1 extra cover plate
 User manual
Some important instructions:
 Before you start using this unit, please check if there's no transportation damage. Should there be any, do
not use the device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
 To protect the environment, please try to recycle the packing material as much as possible.

SAFETY INSTRUCTIONS:

This symbol means: indoor use only
This symbol means: Read instructions
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
 This unit is for indoor use only.
 Don't place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases, shall be
placed on this appliance. Electric shock or malfunction may result. If a foreign object enters the unit,
immediately disconnect the mains power.
 No naked flame sources, such as lighted candles, should be placed on the appliance.
 Prevent use in dusty environments and clean the unit regularly.
JB SYSTEMS 1/25
®
OPERATION MANUAL
LED WALL DIMMER
ENGLISH
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don't use this unit at higher ambient temperatures.
 The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the rear panel of the unit.
 In the event of serious operating problems, stop using the appliance and contact your dealer immediately.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
MAINTENANCE
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.
INSTALLATION
Use CAT5e UTP cable for the connections. This is standard Ethernet computer network cable that you can
easily find in any computer shop. It's important that you follow the color codes for proper installation:
 BLUE = +12V
 WHITE/BLUE = 0V
 WHITE/BROWN = signal ground
 ORANGE = DMX data-
 ORANGE/WHITE = DMX data+
Depending on the application the LED Wall Dimmer
can be used with different JB-Systems LED products:
MICRO LED MANAGER / MINI LED MANAGER Mk2:
 Unplug the LED Manager from the mains.
 Connect the UTP-cable as indicated on the
drawing.
 Set the DMX address of the LED Manager to
address 001.
 Done!
WD MERGER (Wall Dimmer Merger):
The WD Merger makes it possible to connect up to 6 wall dimmers on one DMX line. The DMX-signals from
the 6 LED Wall Dimmers (each 001 to 004) will be merged to one DMX-signal (001 to 024):
 Wall Dimmer1 = 001 to 004
 Wall Dimmer2 = 005 to 008
 Wall Dimmer3 = 009 to 012
 Wall Dimmer4 = 013 to 016
 Wall Dimmer5 = 017 to 020
 Wall Dimmer6 = 021 to 024
ANY OTHER JB SYSTEMS LED PRODUCT:
You can also use it together with other JB Systems
LED products like LED Ball, LED Par,
SPOT/WASH, LED MANAGER 300W, ... However in
these cases you will need a separate +12Vdc power
supply connected to the Wall Dimmer. The DMX
outputs will be connected via a good quality balanced
DMX- cable and XLR-connector. The connected LED
product should be assigned to DMX address 001.
JB SYSTEMS 2/25
®
OPERATION MANUAL
®
LED
LED WALL DIMMER