Checks Before Use; Preparing The Machine And Choosing The Cycle; Drying Cycle; Using The Machine - Truvox International ORBIS BATTERY SCRUBBER Manual Del Usuario

• Turn on the tap and fill the tank.
• Pour the liquid detergent into the tank.
• Once the tank is filled remove the filling hose and insert
the filter supplied into the tank.
• The tank capacity is 17 litres. Do not overfill the tank as
spillage may occur when in use.
IMPORTANT - When the solution tank has emptied,
switch off the machine and empty the recovery tank
before refilling the solution tank. IMPORTANT - Only
chemicals recommended by the appliance manufacturer
should be used, i.e. non-foaming, and follow the chemical
manufacturers' directions
disposal and health and safety provisions. WARNING - If
the detergent comes in contact with the eyes and/or skin
or if swallowed, refer to the use and safety information
booklet provided by the manufacturer of the detergent.
3. Controls
The operating controls are located on the handle (2) and
indicated in the logos below the buttons (B-D). Please
refer to page 1.
Fig. 6
3.1 LEDs status of battery charge (A)
When the brush button is pressed (C) it is
illuminated and indicates the charging status
of the battery.
• When LED (1a) is illuminated, it indicates
that the battery charge status is at
maximum.
• When LED (1b) is illuminated, it indicates
that the battery charge status is at about
half.
• When LED (1c) is illuminated (red LED) it indicates that
the battery charge is at minimum. When the battery is
discharged (red LED 1c), the machine turns off or will
not start and the red LED "R" (Fig. 6) of the battery
charger flashes for a few seconds. At this point the
battery requires recharging.
4. Operation

4.1 Checks before use

• Check the status of the battery charge by the indicator
(A).
• Check the drain hose tube of the recovery tank is
properly coupled and sealed.
• Check that the squeegee vacuum hose is correctly
coupled and inserted in the recovery tank (14 & 15).
• Check that the connector on the squeegee is not
blocked and that the hose is connected correctly (Fig.
7).
regarding use, handling,
Fig. 7
• Check the status of the battery charge by pressing
button C.
• Check water filter is clean and free of debris (Fig. 18).

4.2 Preparing the machine and choosing the cycle

• Press the brush motor button (C), the light illuminates.
• Pull the squeegee lifting lever (3) and release it to lower
the squeegee to the floor.
The machine can perform 4 working cycles:

Drying cycle

• To perform the drying cycle, pull lever 4 to start brush
rotation and press button B to start the vacuum.
Brushing only cycle
• To operate the rotating brush only press lever 4.
Releasing the lever stops the brush.
Washing, brushing cycle:
• Press button D to prepare for the dispensing of solution,
then press lever 4 to release solution onto floor.
Washing, brushing, drying cycle
• Press button B to start the vacuum, button D to release
solution and press lever 4 to start the cycle.

4.3 Using the machine

WARNING - Never start the machine without a brush or
pad fitted.
With the handle set at a comfortable working height
• Start the machine by pressing brush motor button (C)
and select the type of cycle. Start the cleaning operation
by pressing the lever (4) and holding it pressed to start
rotation of the brush or pad and the dispensing of
cleaning solution, and then push the machine in a
forwards direction by means of the handles on the
handle bar.
• Releasing the lever (4) stops the rotation of the brush
and the dispensing of water.
• WARNING - To avoid damaging the floor, do not use the
machine in a fixed position with the brush rotation
activated.
• IMPORTANT – The correct way of cleaning and drying
the floor is to move the machine forwards. Moving the
machine backwards damages the blades as well as not
allowing correct vacuum of the water from the floor.
• If necessary, adjust the quantity of solution flow using
the tap (Fig. 8 & 9).
Fig. 8 Water regulation tap fully opened
Fig. 9 Water regulation tap fully closed
6