Sony DR-E10iP Manual De Instrucciones

Stereo
Headset
DR-E10iP
©2010 Sony Corporation Printed in Thailand






4-180-210-11(1)
Operating Instructions
Manual de instrucciones
English
Stereo headset
WARNING
To reduce the risk of fire or electric
shock, do not expose this
apparatus to rain or moisture.
To reduce the risk of electrical
shock, do not open the cabinet.
Refer servicing to qualified
personnel only.
You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.
Features
 Easy-to-use remote control (only for
iPod and iPhone).
 In-line microphone for hands-free
phone calls of iPhone.
 Earbud style headset in fashionable
colors.
 Neodymium magnet delivers
powerful sound.
How to use
Wearing the headphones
(see fig. )
Wear the earpiece marked  in your
right ear and the one marked  in
your left ear.
If the headphones do not fit your ears,
put on the supplied earpads.
(See fig. )
How to use the cord slider
(see fig. -)
Move up and down to change the split
position of the cord.
How to use the remote
and microphone for an
iPod and iPhone
(see fig. -)
You can control a connected iPod and
iPhone product.
Parts and controls
 Volume +
Increases the volume of the connected
iPod product.
 Center button
Plays/pauses a track of the connected
iPod product with a single press. Skips
to the next track with a double press.
Skips to the previous track with a triple
press. Starts the "VoiceOver*" feature
with a long press (if available).
Press once to answer the call. Press
again to end.
Hold down for about two seconds to
reject an incoming call.
When you let go, two low beeps
confirm the call was rejected.
 Volume –
Decreases the volume of the connected
iPod product.
 Microphone
Compatible products
You can use the unit with only the
following models supporting remote
control.
 iPod nano 4th generation (video)
 iPod nano 5th generation (video
camera)
 iPod classic 120GB 160GB (2009)
 iPod touch 2nd generation
 iPod shuffle 3rd generation
 iPhone 3GS
* Availability of the "VoiceOver" feature
depends on iPod and its software version.
Specifications
Receiver
Type: Open air, dynamic
Driver unit:
13.5 mm, dome type
(CCAW)
Power handling capacity:
100 mW (IEC*)
Impedance:
16 Ω at 1 kHz
Sensitivity:
104 dB/mW
Frequency response:
18 – 22,000 Hz
Cord: 1.2 m (47 / in), Litz cord
1
4
Y-type
Plug: Four-conductor gold-plated
stereo mini plug for iPod
and iPhone with remote
function
Mass: Approx. 6 g (0.21 oz)
without cord
Microphone
Open circuit voltage level:
– 42 dB ( 0 dB=1 V/Pa)
Supplied accessories
Earpads (2)
Card warranty (1)
Operating Instructions (1)
* IEC = International Electrotechnical
Commission
Design and specifications are subject
to change without notice.
Precautions
 Listening with headphones at high
volume may affect your hearing. For
traffic safety, do not use while
driving or cycling.
 Be careful not to allow any buttons
to be unintentionally pressed when
the headphones with iPod/iPhone
connected are in a carrying pouch,
etc.
Note on static electricity
In particularly dry air conditions, mild
tingling may be felt on your ears. This
is a result of static electricity
accumulated in the body, and not a
malfunction of the headphones.
The effect can be minimized by
wearing clothes made from natural
materials.
On copyright
iPod and iPhone are trademarks of
Apple Inc., registered in the U.S. and
other countries.