Safety Of Others; Residual Risks - BLACK&DECKER KR800 Manual De Instrucciones

14 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
Warning! Additional safety warnings for drills and
impact drills.
f Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
f Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
f Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
f Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
f Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling,
as it may be hot.
f The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury and/or damage
to property.

Safety of others

f This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance
by a person responsible for their safety.
f Children should be supervised to ensure that they
do not play with the appliance.
Construction

Residual risks

Earthing
Additional residual risks may arise when using the
Terminal
tool which may not be included in the enclosed safety
Safety Alert
warnings. These risks can arise from misuse, prolonged
Symbol
use etc.
Revolutions
or Recipro-
Even with the application of the relevant safety regulations
cation per
minute
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
f Injuries caused by touching any rotating/moving parts.
f Injuries caused when changing any parts, blades
or accessories.
f Injuries caused by prolonged use of a tool. When
ADDITIONAL POWER TOOL
SAFETY WARNINGS