Super Ego ROBEND 3000 Manual Del Usuario página 10

OPERATING INSTRUCTIONS
MACHINE COMPONENTS (See figure A)
1. Motor
2. Reverse lever
3. Handle
4. Bolt housing
5. Tripod
6. Former
7. Former hook
8. Former fastening shaft
9. Slide
10. Slide fastening bolt
11. Series bending scale
UA-10
CAPACITY
Hartes und weiches kupferrohr DIN 1786 Durchmesser 12-28 mm, Wandstärke 1,5 mm
Hartes und weiches Stahlrohr DIN 2391, DIN 2393, DIN 2394; Durchmesser 12-28 mm x 2,5 mm
Stahlrohr DIN 2440 1/4" (14 mm), 3/8" (18 mm), 1/2" (2 mm), 3/4" (28 mm)
Nichtrostendes Stahlrohr (INOX) AISI 304 - 316, Wandstärke bis 1,5 mm Durchschnitt 12 - 28 mm
Elektrisch Rohre: 16-20-25-32 mm
Preparation for start-up
1. Working position (See figure B.1)
The position shown in the sketch would be ideal for
comfort and safety during the entire bending process.
2. Working area (See figure B.2)
Before start, the bending area should be clear
from any element that may interfere in the bending
process.
3. Use of extension cords
The extension cable should as thick and short as
possible. It should handle more than 15 Amp., and
never be more than 30 m. in length.
4. Check the state of the on/off switch
Make sure that the on/off switch unlocks
automatically when not pressed.
5. Use of tripod (optional) (See figure B.3)
The sketch shows assembly and coupling of tripod to
bending machine.
6. Device for series bending (See figure B.4)
The unit provides a device for setting the bending
angle automatically from 0º to 180º. To operate,
loosen the graduated scale surrounding the former
shaft and align the desired angle with the inner mark
as shown. Once the angle has been selected, tighten
the screws and proceed according to the "start-up"
chapter.
TECHNICAL CHARACTERISTICS
Bending capacity:
Bending angle:
Voltage:
Absorbed power:
On-switch:
Machine weight:
Machine dimensions:
Complete set weight (12,15,18 and 22 mm): 24 kg.
Box dimensions:
Noise level:
Lp:
Vibration level:
Important: It is not advisable to use this option
on pipes larger than Ø 22 x 1,2 mm.
7. Keepaway from moving parts
Make sure that your hands are not in contact with
moving parts of the machine during the bending
process
Starting up
Before carrying out any operation with this unit,
first read the general safety instructions and
preparation for start-up.
Important: For all bending applications, carefully
follow the steps described beolw
1. Select the tube or pipe to be bent. Choose the
relevant bending former and shoe suited to the tubes
size.
Ensure that the ROBEND
position by starting the motor with the direction lever
in the reserve position until it triggers off and moves
to the neutral position.
2. Place the bending former onto the centrepin. Lay
the tube into the bending former and secure it into
the hook.
Important: Ensure that the tubes is fully inserted
into the hook and has contact with the whole hook
surface.
12 – 32 mm
0º - 180º
230 V 50/60 Hz
100 V 50/60 Hz
110 V 50/60 Hz
1010 W (900W)
Non-blocking
590 x 145 x 215
660 x 430 x 200 mm
100 dBA
5,9 m/s
3000 is set in the start
®
ENGLISH
13 kg.
87 db
2
10