Makita DUC204 Manual De Instrucciones página 5

Ocultar thumbs Ver también para DUC204:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3.
Follow instruction for lubricating and
changing accessories.
4.
Do not modify or attempt to repair the
appliance or the BATTERY pack except
as indicated in the instructions for use
and care.
Cordless Chain saw safety warnings
1.
Keep all parts of the body away from the
saw chain when the chain saw is operat-
ing. Before you start the chain saw, make
sure the saw chain is not contacting
anything. A moment of inattention while
operating chain saws may cause entangle-
ment of your clothing or body with the saw
chain.
2.
Always hold the chain saw with your
right hand on the top handle and your
left hand on the front handle. Holding the
chain saw with a reversed hand configura-
tion increases the risk of personal injury and
should never be done.
Hold the power tool by insulated grip-
3.
ping surfaces only, because the saw
chain may contact hidden wiring. Saw
chains contacting a "live" wire may make
exposed metal parts of the power tool "live"
and could give the operator an electric
shock.
4.
Wear safety glasses and hearing protec-
tion. Further protective equipment for head,
hands, legs and feet is recommended.
Adequate protective clothing will reduce
personal injury by flying debris or accidental
contact with the saw chain.
5.
Always keep proper footing.
When cutting a limb that is under tension
6.
be alert for spring back. When the tension
in the wood fibres is released the spring
loaded limb may strike the operator and/or
throw the chain saw out of control.
7.
Use extreme caution when cutting brush
and saplings. The slender material may
catch the saw chain and be whipped toward
you or pull you off balance.
8.
Carry the chain saw by the front handle
with the chain saw switched off and
away from your body. When transporting
or storing the chain saw always fit the
guide bar cover. Proper handling of the
chain saw will reduce the likelihood of acci-
dental contact with the moving saw chain.
9.
Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain
may either break or increase the chance for
kickback.
10. Keep handles dry, clean, and free from
oil and grease. Greasy, oily handles are
slippery causing loss of control.
11. Cut wood only. Do not use chain saw
for purposes not intended. For example:
do not use chain saw for cutting plastic,
masonry or non-wood building materials.
Use of the chain saw for operations different
than intended could result in a hazardous
situation.
12. Causes and operator prevention of
kickback:
Kickback may occur when the nose or tip
of the guide bar touches an object, or when
the wood closes in and pinches the saw
chain in the cut. Tip contact in some cases
may cause a sudden reverse reaction, kick-
ing the guide bar up and back towards the
operator. Pinching the saw chain along the
top of the guide bar may push the guide bar
rapidly back towards the operator. Either of
these reactions may cause you to lose con-
trol of the saw which could result in serious
personal injury. Do not rely exclusively upon
the safety devices built into your saw. As
a chain saw user, you should take several
steps to keep your cutting jobs free from
accident or injury.
Kickback is the result of tool misuse and/or
incorrect operating procedures or conditions
and can be avoided by taking proper pre-
cautions as given below:
Maintain a firm grip, with thumbs and
fingers encircling the chain saw han-
dles, with both hands on the saw and
position your body and arm to allow
you to resist kickback forces. Kickback
forces can be controlled by the opera-
tor, if proper precautions are taken. Do
not let go of the chain saw.
Do not overreach and do not cut above
shoulder height. This helps prevent
unintended tip contact and enables
better control of the chain saw in unex-
pected situations.
5
ENGLISH

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Duc254

Tabla de contenido