Chicco Jolie Instrucciones De Uso página 19

• WARNING: Do not short-circuit the battery
er
terminals.
p-
• WARNING: Always remove spent batteries
of
from the toy to avoid the danger of leaka-
ge from the battery which can damage the
al-
product.
le
• WARNING: Always remove the batteries if
the product will not be used for a long pe-
to
riod of time
• WARNING: Remove the batteries from the
m-
music box before disposing of the product.
ly.
• WARNING: Do not burn or dispose of old
le
batteries into the environment. Dispose of
ls,
them at an appropriate differentiated col-
ts
lection point.
of
• WARNING: If the batteries happen to leak
f-
liquid, replace them immediately, making
sure you clean the compartment before-
le
hand; wash your hands thoroughly if you
ld
come into contact with any such liquid.
ed
• WARNING: Always dispose of leaking bat-
teries immediately: they can cause burns or
e-
other types of injuries.
• WARNING: Do not attempt to recharge
to
non-rechargeable batteries: they might ex-
nd
plode.
ld
• WARNING: The use of rechargeable batte-
ng
ries is not recommended as the music box
may not work properly.
n-
• WARNING: If using rechargeable batteries,
remove them from the toy before rechar-
ns
ging them.
it
• WARNING: Do not leave the product out in
on
the rain; water infiltrations will damage the
do
electronic circuit.
il-
• WARNING: Rechargeable batteries must
only be recharged under adult supervision.
CARE AND MAINTENANCE
by
FABRIC COMPOSITION
• LINING: All new materials. Outer surface: 100% polyester Pad-
ding: 100% polyester
nt
• BOOSTER CUSHION: All new materials. 100% polyester outer
ed
cover 100% polyester padding.
• HEAD REST: all new materials, outer lining 50% cotton 50%
ct.
Polyester. Padding 100% Polyester
-C
• WARNING: This product requires periodic maintenance.
• WARNING: The cleaning and maintenance operations must only
be carried out by an adult.
t-
• WARNING: Periodically inspect the bouncing cradle to check for
broken, torn or missing parts. Do not use the product if there are
any signs of wear or damage.
e-
• Please refer to the care label for instructions on how to wash the
fabric parts.
ols
The Product has a fully removable lining.
Hand wash in cold water
Do not bleach
Do not use a dryer
Do not iron
Do not dry clean
• Check that the fabric and stitching are in good condition each
time you wash it.
• Prolonged exposure to direct sunlight can cause the fabric to
fade.
MAINTENANCE
Use a soft damp cloth to clean the toy bar , the hanging wooden
toys and the music box.
(GB) THIS PRODUCT COMPLIES WITH EU DIRECTI-
VE 2002/96/EC.
The crossed bin symbol on the appliance indicates that
the product, at the end of its life, must be disposed of
separately from domestic waste, either by taking it to a
separate waste disposal site for electric and electronic appliances
or by returning it to your dealer when you buy another similar ap-
pliance. The user is responsible for taking the appliance to a special
waste disposal site at the end of its life. If the disused appliance is
collected correctly as separate waste, it can be recycled, treated
and disposed of ecologically; this avoids a negative impact on both
the environment and health, and contributes towards the recycling
of the product's materials. For further information regarding the
waste disposal services available, contact your local waste disposal
agency or the shop where you bought the appliance.
COMPONENTS
A. Front Feet
B. Side feet (X) and (Y) with joints to adjust the tilt angle of the
bouncing cradle
C. Front seat support with music and vibration box
CC. Music and vibration box
a. Menu button:
a.1 Box OFF button
a.2 Relaxing tunes selector (5 tunes)
a.3 Nature sounds selector (3 sounds)
b. Relaxing tunes and nature sounds browse button
c. Vibration button (2 levels)
d. Volume button (2 levels)
D. Rear seat support
E. Booster cushion; EE. Headrest
F. Seat;
FF. Crotch strap;
FFF. Lap belt
G. Toy bar
GG. Toy bar rotating fixtures
H. Hanging toys
ASSEMBLY
The bouncing cradle requires a quick assembly process before being
used.
Remove all the packaging carefully.
Grasp the front legs (A) and connect them to the side leg X, as
shown in diagram no. 1, so that the tilt angle adjuster fixture but-
ton is on the outside.
Insert the pin to connect the front legs to the side leg X tube, you
will hear it click into place when positioned correctly (diag. 2).
Repeat the above procedure for side leg Y, checking that you hear
it click into position correctly (diag. 3). Check that the structure is
assembled as shown in diagram 4 and the 2 pins at the base of the
front legs are connected properly.
Connect the front seat support (C ) to the relative fixtures (diag. 5)
19