Troubleshooting; Sound Quality - JBL On Time 400iHD Guia Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

SPECiFiCATiOnS
jbl On Time
400
HD
i
Frequency Response: 75Hz – 20kHz
Power Consumption: 30 Watts maximum
JBL On Time
400IHD Transducer: Phoenix SE
1-3/4" (45mm) x 2 (full range per channel)
Power: 6 Watts x 2 < 1% THD
Input Impedance: >5k Ohms
Signal-to-Noise Ratio: >75dB
Input Sensitivity: 500mV RMS for rated power output
Power (USA/Canada): 120 Volts, 60Hz AC
UL/CUL/CE-Approved
Dimensions: 14-3/16" x 5" x 3-1/16"
(W x D x H) (361mm x 128mm x 79mm)
Weight: 2 lb (0.9kg)
DiSPoSal: Do not dispose of this
product as unsorted municipal
waste. Collection of such waste
separately for special treatment is
necessary.
imPortaNt: Use UM4/AAA/LR03
alkaline-type nonrechargeable
batteries only.

TROUblESHOOTinG

sOunD QualiTY

Symptom
Possible Problem
No sound from the
No power to the unit
JBL On Time
400IHD
speaker dock
Incorrect source selection
No sound or weak signal from
Bad reception from current location
the AM/FM radio
Interference
Sound comes only from one
iPod or audio cable is not seated
side/channel
properly
Distortion (static, crackling or
Noise may be caused by interference
hissing sounds)
from a monitor, cell phone or other
transmitting device
JBL On Time 400IHD unit is being over-
driven by an amplified audio source
Volume level may be too high
Too much bass or treble
Check the EQ setting on your iPod or
source device
JBL On Time 400IHD unit emits
Input cables not plugged in properly
a loud hum or buzzing noise
Speaker system experiences
Input cable may be picking up
radio frequency interference
interference
or picks up a radio station
Solution
Make sure the wall power outlet or power strip has
power. Make sure all switches for outlet/power
strip are on and that all switches for speaker
system are on.
Ensure that the correct source is selected; choose
FM radio as a source. Turn up the volume. Check
the system with a known good source, such as your
iPod. Connect the Aux In cable to the headphone
jack on your iPod.
Reposition your JBL On Time 400IHD unit until you
find better reception.
Check surrounding area for any possible
interference; wrap up any excess cables.
Make sure the iPod or Aux In cable is seated all the
way into the JBL On Time 400IHD unit.
Turn monitor off to see whether noise is eliminated.
Move JBL On Time 400IHD unit's cables farther
away from monitor.
Ensure that the unit is connected to an appropriate
source device. Make sure that all signal cables are
inserted snugly into receptacles.
Check volume of source device; some devices
will distort the output signal if the volume is set to
Maximum.
We recommend that the source device EQ be set
to Flat or Off.
Check input cable connection.
Wrap up excess input cable to make it as short
as possible.
Purchase a ferrite clamp and attach it over the
input cable; a clamp can be purchased at your local
electronics store.
www.jbl.COM
Note
Is the display on? If not,
power is not getting to your
JBL On Time 400IHD unit;
try the solutions shown.
If you are still getting a weak signal
from AM broadcasts, connect the
external AM antenna to the AM
antenna jack.
If you are using an extension cable
or a third-party cable, make sure it's
a 3.5mm stereo male-to-male cable.
21

Publicidad

Tabla de contenido
loading

Tabla de contenido