Cleaning The Machine - GGP ITALY EL 340 Li 48 Manual De Instrucciones

interchangeable and operating safety features.
Reassemble the cutting means (2) with the code facing
the ground, following the steps indicated in the illustration.
Tighten the central screw (1) using a dynamometric key
calibrated at 30 Nm (for model 340) or 16-20 Nm (for model
380 - 420).

4.3 Cleaning the machine

Do not spray water onto the motor and electrical compo-
nents and prevent them from getting wet.
Do not use aggressive liquids to clean the chassis.
4.4 BATTERY RECHARGING AND HANDLING
NOTES
1. The battery must be stored in places with temperatures
between +7°C and +40°C. If the machine is stored in
places that could exceed these threshold, it is recom-
mended to remove the battery and store it in a more
suitable location.
2. During use, the battery is protected against total drain-
age with a protective device that switches off the ma-
chine and stops it from working.
3. The battery is equipped with a guard that inhibits re-
charging if the environmental temperature is not be-
tween 0 and +45 °C.
4. The battery can be recharged at any time, even partially,
with no risk of damaging it.
4.4a Checking the battery charge status
To check the condition of the battery charge status (4),
press the small button (4a) which activates four LED lights
(4b) which indicate the following:
Battery power reserve
LED
4 GREEN
100%
3 GREEN
70%
45%
2 GREEN
1 GREEN 10% - Recharge needed
The battery has less than 10% power re-
None
serve and needs recharging immediately.
If at least one LED does not come on after
30 minutes charging, the battery is faulty and
needs replacing.
4.4b Battery removal and recharging
After every work session, the battery should be recharged.
To recharge the battery:
– open the hatch (1) and remove the safety key (2);
– press the bottom tab (3) and remove the battery (4);
– insert the battery (4) in its housing in the battery charger
(5), pushing it in completely.
– connect the battery charger (5) to a power socket with the
voltage indicated on the rating plate.
Battery charging lasts from 1.5 - 3.5 hours, depending on
the battery capacity and its residual charge.
The battery charger (5) is the diagnostic type fitted with a
LED that provides information on the battery and charge
status, based on the following chart:
LED (5a) Meaning
Battery charging
GREEN
(Flashing
Fully charged battery
GREEN
Battery overheated: remove the
RED
battery and leave it to cool for at least
30 minutes
No battery or battery inserted incor-
Off
rectly
Charge anomaly and possible faulty
RED
battery; in this case remove the
(Flashing)
battery and replace it within 2 hours:
if the LED indicates charging status,
this means that the battery is in
good condition and the charging can
proceed as normal. Otherwise:
– disconnect the battery charger, wait
– remove the battery from the
If, after all these attempts, the LED
(5b) does not indicate the charge
status and continues to flash, this
means that the battery is faulty and
needs replacing.
4.4c Refitting the battery on the machine
When recharging is completed:
– press the lower tab (3) and remove the battery (4) (do not
keep recharging when recharging is completed);
– disconnect the battery charger (5) from the mains pow-
er supply
– open the hatch (1) on the machine, insert the battery (4) in
its housing on the machine and push in all the way to lock
it into place and ensure electrical contact.
– completely close the hatch (1) again.
5. ATTACHMENTS
WARNING!
For your safety, it is strictly prohibited
to fit any other attachment other than those included
in the following list, as they have been exclusively de-
signed for the model and type of machine you are using.
5.1 Alternative batteries
Different capacity batteries are available to suit specific op-
erating requirements. The list of approved batteries for this
machine is found in the table on page «ix».
6. DIAGNOSTICS
Problem description
1. The motor does not start
when the switch is pressed
Safety key is not inserted
or is inserted
incorrectly
7
a few minutes, and reconnect it to
the mains again;
charger, wait a few minutes, and
replace it again.
What to do if ...
Corrective action
Insert the key until you
here it "click" (see 3.2)