PLYMOVENT CONTROL PRO Manual De Instalación página 12

Fig. 4.17
• Make sure that DIP switches position 5+6 are correctly set.
Configuration of filter module :
MDB-BM/2
MDB-BM/2 +
pos. 5+6
MDB-BM/4 +
Fig. 4.17 DIP switches position 5+6
Address configuration:
Fig. 4.18
1
• Set the DIP switches 1 to 4 as indicated. It shows the
0000112547/A
address configurations of max. 16 filter modules
2
(=MDB-64).
9
0000112547/A
2
3
attENtioN
10
Make sure that you address the filter modules in the
4
correct sequence:
11
- start with the upper left filter module (1)
- address from left to right 5
4
12
Addressing
- subsequently from top to bottom
sequence:
6
13
Addressing
Addressing sequence
7
14
sequence:
8
15
1 2
16
1 2
3 4
3 4
Fig. 4.18 Setting of DIP switches pos. 1 to 4
• Close all lids.
Digital input 1-5
If there is a technical problem with a certain filter module, the
HMI shows the specific number. The outside of the lid contains
1 2 3 4 5 6 7 8 9 10 11 12
a sticker that helps you to identify each separate filter module.
Fig. 4.19
• Use a black marker to number the filter modules. Make
sure that the sequence corresponds with the setting of the
DIP switches.
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Fig. 4.19 Numbering of the filter modules
4.4.6 Compressed air switch MDB
The compressed air switch monitors the availability of
Digital input 6-12
compressed air .
24
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
24. The system gives a warning signal when there is no compressed air available
0000112606/200917/0 ControlPro
Digital input 6-12
MDB-BM/4
pos. 5+6
9
10
Configuration of filter module :
MDB-BM/2 +
11
Configuration of filter module :
12
MDB-BM/4 +
MDB-BM/2 +
13
Address configuration:
MDB-BM/4 +
14
1 9
Address configuration:
Address configuration pos. 1-4
15
2 10
1 9
16
3 11
2 10
4 12
3 11
5 13
4 12
6 14
5 13
7 15
6 14
8 16
7 15
8 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Power
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12
Fig. 4.20 Connection of compressed air switch
• Proceed with paragraph 4.4.8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
4.4.7 Compressed air switch + valve SCS / EDS
In case of one (1) SCS / EDS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Besides the compressed air switch, cable #20 connects the
compressed air valve of the SCS / EDS as well.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Valves
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 Power
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Valves
1 2 3 4 5 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Fig. 4.21 Connection of compressed air switch + compressed air valve
Valves
1 2 3 4 5 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Digital input 6-12
Digital input 6-12
Dustbin Fan Pressure
Digital input 1-5
Indicator LED's
sensor sensor
Analog Filter Pressure
Light tower
output sensor
Digital input 6-12
Digital input 1-5
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
Dustbin Fan Pressure
Digital input 1-5
Indicator LED's
sensor sensor
Analog Filter Pressure
Light tower
output sensor
Digital input 6-12
Digital input 6-12
Digital input 6-12
RS485 VFD CAN Slave
CAN HMI
Digital input 6-12
cable #10
[page 8]
input IN 10
Digital inp
1 2 3 4 5 6 7
RS485 VFD CAN Slave
Digital input 6-12 CAN HMI
cable #20
[page 8]
input IN 10
input OUT 1
EN - 11
1
1
1
1