Tool Specifications; Machine Elements; For Your Safety - Bosch GWS 24-300 Instrucciones De Servicio

1 609 929 355.book Seite 1 Dienstag, 23. März 2004 12:51 12

Tool Specifications

Cut off grinder
Order number
With residual current-limit
control
Order number
Rated input power* [W]
Output power [W]
No-load speed [rpm]
Grinding disc dia.,
max. [mm]
Grinder spindle
thread
max. cutting depth
with cutting guide [mm]
Weight without
cable, approx. [kg]
Protection class
* The values given are valid for nominal voltages [U] of
230/240 V. For lower voltages and models for specific
countries, these values can vary.
Please observe the order number of your machine.
The trade names of the individual machines may vary.
Inrush currents cause short-time voltage drops. Under un-
favourable power supply conditions, other equipment may
be affected. If the system impedance of the power supply
is lower than 0.25 Ohm, disturbances are unlikely to occur.

Machine Elements

The numbering of the machine elements refers to
the illustration of the machine on the graphics
page.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
1 Bow handle
2 Spindle lock button
3 Grinder spindle
4 Protection guard
5 Adjustment screw
6 Clamping lever
7 Mounting flange*
8 Cutting disc*
9 Face plate
10 quick-clamping nut*
11 Clamping nut
12 Allen key
13 Guide plate
14 Thread for auxiliary/bow handle
12 • 1 609 929 355 • TMS • 15.03.04
15 On/Off switch
16 Coded projection
GWS 24-300
17 Protective cover with cutting guide *
PROFESSIONAL
18 Elbow*
0 601 364 0..
19 Cutting grinder stand*
GWS 24-300 J
* Not all of the accessories illustrated or described are
PROFESSIONAL
included as standard delivery.
0 601 364 9..
2 400
1 670
5 000
300
M 14
100
general safety notes in the enclosed booklet
must be observed. Before using for the first
time, ask for a practical demonstration.
6.2
Wear protective glasses and hearing protec-
/ II
tion.
Wear additional protection equipment for your
safety, such as protective gloves, sturdy
shoes, hard hat and apron.
The dust that is produced while working can be
detrimental to health, inflammable or explo-
sive. Suitable safety measures are required.
Examples: Some dusts are regarded as carci-
nogenic. Use suitable dust/chip extraction and
wear a dust protection mask.
Dust from light alloys can burn or explode. Al-
ways keep the workplace clean, as blends of
materials are particularly dangerous.
If the mains cable is damaged or cut through
while working, do not touch the cable but im-
mediately pull the mains plug. Never use the
machine with a damaged cable.
Connect machines that are used in the open
via a residual current device (RCD) with an ac-
tuating current of 30 mA maximum. Do not op-
erate the machine in rain or moisture.
When working with the machine, always hold it
firmly with both hands and provide for a secure
stance.
Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
securely than by hand.
Always direct the cable to the rear away from
the machine.
Always switch the machine off and wait until it
has come to a standstill before placing it down.
For power outage or when the mains plug is
pulled, unlock the On/Off switch immediately
and turn it to the Off position. This prevents un-
controlled restarting.
English - 1

For Your Safety

Working safely with this ma-
chine is possible only when the
operating and safety information
are read completely and the in-
structions contained therein are
strictly followed. In addition, the