Kinderkraft XMOOV Manual De Usuario página 24

I Buggy components
A. Frame
B. Parent handle
C. Front wheels x2
D. Rear wheels x2
E. Safety bar
F. Seat/bassinet 2 in 1
G. Element of bassinet rack/seat
H. Mattress
I. Hood
II BUGGY FRAME ASSEMBLY To initially unfold the frame, unlock the hook (FIG. 1) and then simultaneously pull the two
free ends of the frame, until you hear the lock click (FIG. 2). Insert the rear wheel axles (D) in the corresponding slots until
you hear the lock click (FIG. 3). Slide the front wheels (C) in the corresponding slots until you hear the lock click (FIG. 4).
In the next step attach free ends of the basket (K) to the frame (FIG. 5). Insert the ends of the parent handle (B) in the
free ends of the frame (FIG. 6). Make sure the latches are secured (FIG. 6A). An unfolded frame is shown in Figure 7.
WARNING! The buggy has pumped wheels. Do not exceed the
maximum permissible pressure in the wheels, the value is
indicated on the wheel tyres.
WARNING! Before using the buggy, make sure that all the
wheels are properly installed.
III BASSINET ASSEMBLY
(G) into the slots in the bassinet (F) (FIG. 8). Make sure the latches are secured (FIG. 8A). Then fasten the zip fastener on
the perimeter of the mounted part (FIG. 9). Adjust the rod under the bassinet with straps and secure with snaps (FIG. 10).
A complete bassinet is shown in Figure 11. The bassinet can now be attached to the buggy frame (you will hear the sound
of the locks on both sides of the buggy) (FIG. 12).
WARNING! THE BASSINET CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
IV ASSEMBLY OF SAFETY BAR, HOOD, FOOTMUFF AND MUG HOLDER The safety bar (E) should be used in both the
bassinet and the pushchair. Insert the tips of the safety bar in the corresponding slots until you hear the locks on both
sides (FIG. 13).
Start the installation of the hood (I) from inserting plastic clips in the fastenings in the bassinet/seat frame (FIG. 14).
Proper protection is indicated by a quiet click. Lastly, secure the hood with Velcros (FIG. 15) and wrap around the tilt
angle adjustment lever (Fig. 16).
Start the installation of the footmuff (J) from pulling it as shown in Figure 17. Wrap the ribbons on both sides of the safety
bar and secure with snaps (FIG. 18). Wrap the free end of the footmuff around the safety bar and secure with buttons
(FIG. 19). Additionally, attach both ends of the footmuff to the shell (FIG. 20). The mug holder (P) is assembled on a pin
at the right side of the stroller (FIG. 21).
V CONVERTING THE BASSINET INTO THE SEAT To convert the bassinet into the seat, you must first pull out the belts on
both sides of the shell (FIG. 22) and under the footrest. Connect the ends of the belts behind the back, under the seat
and the footrest (example Figure 23). Properly fastened belts should look as shown in Figure 24 (seat angle control
method described in section VIII).
VI MOUNTING THE BAG, MOSQUITO NET AND RAIN COVER The XMOOV stroller set includes: bag (M) with baby changing
mat (N), silicone hangers (O), rain cover (Q) and mosquito net (R). Use the silicone hangers to hang the bag on the parent
handle (FIG. 25).
Place the mosquito net and secure with Velcros. Place the rain cover on the buggy and secure with Velcros around the
frame (FIG. 26).
VII MOUNTING THE BABY CAR SEAT The supplied adapters (L) are compatible with the following car seats: Kinderkraft,
Maxi Cosi®, ybex® and are suitable for models such as: inderkraft M N , ybex Aton, Aton 2, Aton Q i Maxi osi Mico,
Mico AP, Mico NXT, Mico Max 30, Citi, Cabrio, and CabrioFix.
Slide the adapters into the slots in the frame until you hear the sound of the lock (FIG. 27). The adapters should be slightly
tilted to the parent. Put the seat in the adapters and make sure it is properly secured. XMOOV buggy with MINK car seat
The assembly of the bassinet should begin with inserting the loose part of the frame
24
J. Footmuff
K. Basket
L. Car seat adapters x2
M. Bag
N. Baby changing mat
O. Silicone hangers x2
P. Mug holder
Q. Mosquito net
R. Rain cover