Field Of Application; Product Description; Particular Advantages; Technical Data - Trisk CureMate 2 Manual De Funcionamiento

English
2.

Field of application

A mobile dryer is an essential aid for paint repair
on small and medium-sized areas.
It is used to accelerate the drying of putty, filler,
base and top coats. This applies to both water-
based and solvent-based products. Its site of use is
the preparation area and finishing area. Within the
automotive industry and vehicle maintenance sec-
tors, it is used to dry small areas and cure materials
on vertical surface before polishing.
3.

Product description

The easily manoeuvrable CureMate 2 is equipped
with a compact cassette. The cassette is equipped
with 3 IR lamps with aluminium reflectors and a
ventilator. The design makes cassette adjustment
simple. The IR lamps and reflectors are protected
against mechanical damage with a mesh. The con-
trol unit enables flash off (50% heat applying) and
full bake (100% heat applying). The time can be
set individually for each status.

3.1 Particular advantages

3.1.1 Higher quality
Using the mobile dryer when you dry putty also
improves the quality of the top coat. The high
surface temperature and curing from the inside
outwards drive all solvents and other reaction prod-
ucts from the coated material.
3.1.2 Short drying times
Putty 3 -5 min.
Filler 5 - 10 min.
Primer 8 - 12 min.
Water-base 4 - 6 min.
Base coat 4 - 8 min.
Top coat 8 - 12 min.
Clear varnish 8 - 12 min.
3.1.3 Low energy consumption
Electrical energy is used efficiently through short-
wave technology and aluminium coated reflectors.
Surfaces are subjected to targeted irradiation. The
air is not heated.
3.1.4 Good maneuverability
The units low weight makes the machines very
competitive, versatile and easy to use.

3.2 Technical data

Electrical diagram
See chapter 11
For machine reach and dimensions, see last page
421062 rev 1
Rated Voltage 220V - 240 V, 50/60Hz
Single Phase
Rated power 3 emitters, full power 3000 W
Heating elements 3 quartz, tungsten filament,
InfraRed emitters
Fuse 16 A slow, type C (UK 13A)
Drying surfaces on 1 m x 0.90 m
black sheet metal
Dimensions See last page
Weight 23 kg
Noice level Less than 70 dB (A)
Max ambient tempera-
ture during operation 40
Max ambient tempera-
ture during storage
and transportation 70
4.

Instruction to the owner

The owner of the mobile dryer must produce clear
operating instructions, adapted to local site condi-
tions, and make these available to all users.
Mobile dryer users must adhere to these operating
instructions.
Dispose of spent items at the nearest environmental
protection facility for recycling.
5.

Hazards

Fire and explosion
Do not use the mobile dryer in rooms or areas
where there is risk of explosion, e.g. in the spray
booth.
Do not store, prepare or use solvent-containing
materials within a 5 m radius of the mobile dryer.
Where possible, avoid exposing the mobile dryer
to paint fog, sanding dust or solvents.
The distance between the cassette and the object to
be dried should never be less than 60 cm.
Never direct the cassette towards highly combus-
tible material.

Electrical equipment

The mobile dryer is operated by highly dangerous
electrical voltage.
Accessing electrical equipment
Remove main connector from wall socket. Only
professional electricians may have direct access
into the electrical equipment.
WARNING!
Intensive heat radiation. Hands, face and other
parts of the body should be exposed as little as
possible to the heat radiation.
CureMate 2
o Celsius
o Celsius
5