Main Section - Samson TM300 Manual De Instrucciones

Guided Tour - Main Section
TAPE IN
–10dB
L R
1
AUX RET1
+4dB
2
L/MONO
AUX RET 2
SAMSON
7
0
8
+10
TAPE IN REC OUT
0
9
+10
AUX RET 1 AUX RET2/REV
10
0
+10
AUX SEND 1 AUX SEND 2
DSP
0
16
VOCAL
+10
REV TO AUX 1
L HALL
17
S HALL
18
ON
10 10
0 0
4 4
22
8 8
12 12
16 16
20 20
26 26
O O O O O O O O O O O O O O O O
L –STEREO–
3
REC OUT MONO OUT+4dB
+4dB
L R
INSERT
R L MAIN R
POST EQ
LEFT RIGHT
AUX1 AUX2
POWER
+4
+4 +4
+2 +2
0
0 0
PHANTOM
-2 -2
+10
-4 -4
-9 -9
0
-12 -12
METER HEADPHONE
+10
SOURCE
-15 -15
-20 -20
-25 -25
6 CHANNEL 150 WATT STEREO MIXER
AUX 1/MONITOR EQ ON/OFF
LEFT
63Hz 160Hz 400Hz 1KHz 2.5KHz 6.4KHz
L
63Hz 160Hz 400Hz 1KHz 2.5KHz 6.4KHz
R
63Hz 160Hz 400Hz 1KHz 2.5KHz 6.4KHz
0
+10
LEVEL
HEADPHONE
R
6: Aux Sends (1, 2) - These unbalanced 1/4" jacks allow you to route signal from either
of the TM300's two discrete Aux Sends to external devices such as effects processors.
Aux send1 is pre-fader, while Aux Send 2 is post-fader. See the "Using Aux Sends and
Returns" section on page 20 in this manual for more information.
1: Tape input (L, R) - Connect the outputs of a
tape or CD player to this set of dual phono jacks.
The volume of the incoming signal is controlled
by the Tape In level control (see #7 on the next
page).
2: Aux Returns (1, 2) - Connect signal from
external stereo devices such as effects proces-
5
sors to these unbalanced 1/4" jacks. See the
"Connecting the TM300" section on page 10 and
AUX SEND 1
the "Using Aux Sends and Returns" section on
page 20 in this manual for more information.
+4dB
6
3: Record outputs (L, R) - This set of dual
phono jacks allow you to connect the output of
AUX SEND 2
the TM300 to the inputs of a two-track recorder.
4
The volume of the incoming signal is controlled
11
by the Record Out level control (see #8 on the
next page). See the "Connecting the TM300"
12
section on page 10 in this manual for more
information.
13
OFF
14
4: Main Inserts (L, R) - Use these to insert an
ON
external effects processor (such as outboard
L/R
15 equalizer, compressor/limiter or noise gate)
AUX 1/2
across the TM300's main stereo output in an
"effects loop" configuration. This enables you to
19
process the entire mix simultaneously at unity
RIGHT
20
gain. The "Post EQ" pair of Main Inserts is
15KHz
+12dB
affected by both the seven-band graphic master
0dB
equalizer and stereo faders, while the "Pre EQ"
-12dB
pair is not. These jacks accept 1/4" TRS plugs,
21
15KHz
with the ring carrying the send signal and the tip
+12dB
carrying the return signal. Normally, this will be
0dB
connected to a Y-cord; see the "Connecting The
-12dB
TM300" section on page 10 in this manual for
15KHz
more information and a wiring diagram. The Main
23
Inserts can also be used to link multiple TM300s
or to bring the output from another mixer into the
TM300 without taking up channel line inputs.
24
See the "Using Inserts" section on page 21 in
this manual for more information.
5: Mono Out - This unbalanced 1/4" jack pro-
vides a monophonic line-level output, unaffected
by the Stereo faders (see #22 on page 8). It can
be used to connect the TM300 to an external
monitor mixer/amplifier/speaker system so that
performers can receive an onstage monitor mix.
See the "Connecting the TM300" section on page
10 in this manual for more information.
8