Initial Operation/Setting - Metabo SSW 650 Manual Original

Ocultar thumbs Ver también para SSW 650:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20
en
ENGLISH
Original instructions
1. Declaration of Conformity
We declare under our sole responsibility: These
impact drivers, identified by type and serial number
*1), comply with all relevant requirements of the
directives *2) and standards *3). Technical file at *4)
- see page 3.
2. Specified Use
The impact screwdriver is suitable for driving in and
removing screws.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
3. General safety instructions
For your own protection and for the
protection of your power tool, pay atten-
tion to all parts of the text that are marked
with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your electrical tool only together with these
documents.
4. Special Safety Instructions
Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. A cutting acces-
sory that comes in contact with a "live" wire may
render exposed metal parts of the power tool "live"
and give the operator an electric shock.
Pull the plug out of the plug socket before any
adjustments, conversions or servicing are
performed.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Only screwdriving bits suitable for the impact screw-
driver must be used.
Take care when driving in long screws - risk of slip-
ping.
Mount the machine on the screw only when it is
switched off.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be supported adequately.
8
Wear ear protectors when working for long
periods of time. High noise levels over a
prolonged period of time may affect your hearing.
Materials that generate dusts or vapours that may
be harmful to health (e.g. asbestos) must not be
processed.
5. Overview
See page 2.
1 Square attachment for 1/2" tools
2 Rotation selector switch / Transporting safety
device
3 Trigger

6. Initial Operation/Setting

Before plugging in the device, check to see
that the rated mains voltage and mains
frequency, as specified on the rating label, match
your power supply.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual-
current of 30 mA or less.
6.1
Setting the direction of rotation, engag-
ing the transporting safety device
(switch-on lock)
Do not actuate the rotation selector switch or
engage the transportation lock (2) unless the
motor has stopped completely!
Actuate the rotation selector switch / Engage the
transportation lock (2)
R = Right rotation set
(insert screws)
L = Left rotation set
(remove screws)
0 = Central position: transportation lock setting
(switch-on lock)
6.2
Switching on and off
Switching on: press the trigger switch (3).
Switching off: release the trigger switch (3).
6.3
Speed / Tightening torque
The speed and tightening torque are connected
directly. The lower the speed, the lower the tight-
ening torque.
The speed and tightening torque can be adjusted
steplessly by pressing the trigger (3) firmly or lightly,
thus adapting to working conditions.
Recommendation: determine the correct setting
by carrying out trial screwdriving.
6.4
Changing the screwdriving bit
The screwdriving bit used must match the
screw.
Damaged screwdriving bits must not be used.

Publicidad

Tabla de contenido
loading

Tabla de contenido