Use; Setting Speed; Switching On And Off; Working Instructions - Metabo PWE 11-100 Manual Original

17027032_1210 PWE 11-100.book Seite 16 Montag, 20. Dezember 2010 7:55 07
ENGLISH
ENG
To fit:
- Press in the spindle locking button (11) and turn
the spindle (8) by hand until you feel the spindle
locking button engage.
- Manually screw on the support plate (18) (with
velcro-type fastening), turning clockwise.
- Simply press the polishing disc (17) (with velcro-
type fastening) so that the polishing disc (17) and
support plate (18) are perfectly aligned.
To remove:
- Press the spindle locking button (11).
- Manually unscrew the support plate (18), turning
anticlockwise (apply a flat wrench to the spanner
flat of the plate if necessary).

8 Use

8.1

Setting speed

The speed can be preset via the setting wheel (19)
and is infinitely variable.
Positions 1-6 correspond approximately to the
following no-load speeds:
1 ......... 1700 / min
2 ......... 2700 / min
3 ......... 3500 / min
The VTC electronics make material-compatible
work possible and an almost constant speed, even
under load.
8.2

Switching On and Off

Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When
switching the machine on and off, keep it away
from dust deposits. After switching off the
machine, only place it down when the motor has
come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
To switch on: Connect the machine to the power
supply. Push the RESET button (6). Push
the sliding switch (12) forward. For contin-
uous activation, now tilt downwards until it
engages.
Switching off: Press the rear end of the slide
switch (12) and release.
16
8.3
To start work:
- Set up the water connection (see chapter 7.5)
- Test the GFCI (see chapter 7.3).
- Open the shut-off cock (1): water flows from the
- If necessary, adjust the speed. Switch on the
- Fit the accessory on the tool.
- Apply moderate pressure on the machine and
To finish work:
- Remove the accessory from the tool.
- Switch off the machine and allow it to come to a
- Close the shut-off cock (1).
- Store away the machine.
The pilot light (7) does not go out when the
TEST button (5) is pressed. Unplug. You must not
use the machine! Have a qualified electrician
check the machine.
4 ........4100 / min
Restart protection When power is restored after
5 ........4800 / min
a power failure, the machine - which is still
6 ........5400 / min
switched on - will not start for safety reasons. Push
the RESET button (6). The pilot light (7) now lights
up.
The GFCI (4) switches off the machine repeat-
edly when it is turned on. Unplug. You must not
use the machine! Have a qualified electrician
check the machine.
The electronic signal display (13) lights up and
the load speed decreases. The coil temperature
is too high! Run the machine in idling until the elec-
tronics signal indicator switches off.
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.

Working instructions

spindle (8).
machine.
move it to and fro across the surface.
standstill.

9 Troubleshooting

10 Cleaning, Maintenance

11 Accessories

A Diamond cling-fit polishing discs