AEG MC 4401 CD Instrucciones De Servicio página 32

• Insert 2 batteries of type LR 6 „AA" 1,5V. Please
ensure that the polarity is correct (see the fl oor
of the battery compartment or the inscription on
the outside)! If the remote control is not used for a
prolonged period, remove the batteries in order to
prevent battery acid leaking.
• Always replace the complete set of batteries. Do not
replace just one battery.
Warning: batteries are not to be disposed of together
with domestic wastes. Dispose of the used batteries at
the relevant collection bin or at your dealer's.
Never throw batteries into the fi re.
General Operation
POWER (1):
Switches the unit to „ready for
operation" or to „off". The POWER
button lights up in blue.
BASS on/off (8):
to increase or decrease the bass
output.
On = button lights up in blue.
Volume:
You can set the desired volume
using the VOLUME control (25).
PHONES (22):
Insert the plug of a set of head-
phones into the headphone socket
– the loudspeakers are „muted". If
your headphone plug does not fi t,
please use a suitable adapter.
Loudspeakers (24): Connect the loudspeakers to the
connections (30) on the rear.
Infrared
remote control:
For operating the music centre
from a distance of up to 5 metres
without a lead. If the range of the
remote control is reduced, the bat-
teries have to be replaced. When
operating the remote control ensu-
re that there is nothing blocking the
view between the remote control
unit and the infra-red receiver on
the music centre.
Listening to the Radio
1. Turn the function selector switch (26) to the RADIO
position.
2. Select the desired frequency band with the band
selection buttons (9/10).
VHF Stereo = FM
Medium wave = MW/AM (Mono).
3. Tune in the desired station with the station adjust-
ment knob TUNING (14).
4. The STEREO control lamp (6) only lights up when you
have selected FM stereo and the station is being re-
ceived in stereo quality. If reception is too weak and
the station received crackles, it may be that this light
will not come on. Try to improve reception by turning
and bending or twisting and altering the length of the
antenna (32).
5. An aerial is integrated into the device for the recepti-
on of AM stations. The machine can be aligned to the
station by turning it. In this frequency band programs
are transmitted in „mono" only.
32
5....-05-MC 4401 CD AEG 32
Cassette Operation
Playing Cassettes
1. Select the function TAPE (26).
2. Open the fl ap (15).
3. Press the / Stop/Eject button (17) in order to
open the cassette compartment (23).
4. Push a recorded audio cassette, with the tape down-
wards and the listening side facing forwards, into the
compartment. Close the cassette compartment.
5. Press the playback key (20) to listen to the tape.
6. With the í/
stop/eject key (17) you can stop play-
back.
7. Wind the tape forwards or backwards if necessary in
the direction of the arrow keys.
= forwards (18), = reverse (19).
Always press the í/
stop/eject key (17) when
changing the direction or stopping the tape. This
prevents damage to the machine and the tape.
8. If the í/
stop/eject button (17) is pressed again the
fl ap of the cassette compartment opens.
9. In order to interrupt playback briefl y, press the
II PAUSE button (16). Pressing again continues
playback.
Recording Cassettes
1. Insert an audiocassette with the side on which you
wish to record facing forwards. Ensure that the cas-
sette is not copy-protected (the copy protection tab
on the top narrow side of the cassette must not have
been removed).
2. Select the source from which you wish to record with
the function switch (26) and then start playback from
this source if necessary. The sound source which you
are listening to is the one from which the recording is
made. The recording level is controlled automatically.
Any changes to the sound and volume do not affect
the recording.
3. Please press the b record button (21) (the
playback button is automatically pressed down at
the same time). Recording now begins. All previous
recordings are automatically erased.
4. The recording can be interrupted briefl y using the
II pause key (16), or stopped by means of the
stop/eject button (17).
Playing CDs
This is how you play a CD
1. Turn the function selector switch (26) to the „CD"
position.
2. Press the key to open the CD deck cover (7).
3. Insert a music CD with the label facing upwards on the
central button and close the CD deck cover (5).
4. „- -" appears in the display (3) followed by the num-
ber of tracks.
5. Press the /II PLAY/PAUSE button (11/B) to listen to
the CD. The CD will play from the fi rst title. The cur-
rent track and the symbol
6. You can set the desired volume using the VOLUME
control (25).
7. To remove a CD, press the
open the CD deck with the PUSH key (7) and take
out the CD carefully.
/
are shown in the display.
CD STOP key (29/E),
11.02.2004, 11:54:49 Uhr