Tabla de contenido
Publicidad
Enlaces rápidos
a WARNING: Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
Quick-Start Guide
NOTE: Your product may differ slightly from the item shown.
ASSEMBLE SHAFT (MODELS WITH
KNOCKDOWN SHAFT)
a WARNING: To avoid personal injury or damage
to the unit, turn the unit off when assembling or
disassembling the shaft.
CAUTION: When assembling or disassembling the shaft,
1. Align the tab on the coupler (A) with the slot on the
lower tube (B).
2. Press the lower shaft into the coupler until the tube
ends are touching (C).
3. Install the coupler knob (D) on the same side as the
screw head and tighten securely.
CAUTION: To avoid personal injury or damage to the unit,
periodically check to ensure the tube ends are touching
and the knob is tight.
ADJUST HANDLE
1.
Loosen wing nut on handle.
2.
Rotate the handle on the shaft to an upright position; retighten
wing nut.
ATTACH SHIELD
1.
Mount shield to bracket by inserting TAB (A) on shaft bracket into
SLOT (B) in shield.
2.
Rotate shield until bolt goes through bracket.
3.
Attach wing nut (C).
A
FILL TANK
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of gasoline for a
50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
590203803 Rev. A 2018-01-09
B
C
W25CB / W25CBK
W25SB / W25SBK
PLACE IN STARTING POSITION
START COLD ENGINE
Move the choke lever to the full choke
(bottom) position.
Squeeze the throttle trigger while pulling the
starter rope handle 4 times rapidly.
Move the choke lever to the half choke
(middle) position.
Squeeze the throttle trigger while pulling
starter rope rapidly until the engine starts,
but no more than 6 pulls.
attempt, repeat steps 1-5.
If the engine does not start on the second
attempt, refer to the TROUBLESHOOTING
table or call customer support.
Squeeze the throttle trigger and let the
machine run for 15 seconds.
Move the choke lever to the run (top)
position.
Allow the engine to warm up for one minute.
START HOT ENGINE
Follow steps 1,4,5,6,7 in
START COLD ENGINE.
LT25NCOP
LT25NSOP
Publicidad
Tabla de contenido
Manuales relacionados para Weed Eater W25CB
Resumen de contenidos para Weed Eater W25CB
- Página 1 W25CB / W25CBK a WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. W25SB / W25SBK Quick-Start Guide NOTE: Your product may differ slightly from the item shown.
-
Página 2: Identification Of Safety Symbols
Keep cutting line at proper length. manual. Never allow children to operate this unit. • Use only recommended WEED EATER brand line. Never use wire, rope, string, etc. a WARNING: •... - Página 3 CUTTING SAFETY motors or switches, furnaces, etc. a WARNING: Inspect the area before each use. • Store unit so line limiter blade cannot accidentally cause injury. The unit can be hung by the shaft. Remove objects (rocks, broken glass, nails, wire, etc.) •...
-
Página 4: Know Your Trimmer
OPERATION Compare the illustrations with your unit to familiarize KNOW YOUR TRIMMER yourself with the location of the various controls and READ THIS INSTRUCTION MANUAL AND SAFETY adjustments. Save this manual for future reference. RULES BEFORE OPERATING YOUR UNIT. A. Curved shaft models the fuel is thoroughly mixed. -
Página 5: Personal Protective Equipment
STARTING A COLD ENGINE (OR A HOT ENGINE AFTER OPERATING INSTRUCTIONS RUNNING OUT OF FUEL) PERSONAL PROTECTIVE EQUIPMENT Always wear: 1. Hearing protection 2. Eye protection 3. Long pants Move the choke lever to the full choke (bottom) position. 4. Gloves 5. - Página 6 If any dealer other than an authorized service dealer After each use, inspect complete unit for loose or damaged performs work on the product, WEED EATER may not parts. Clean the unit and labels using a damp cloth with a pay for repairs under warranty.
-
Página 7: Service And Adjustments
serviced or replaced by your authorized service dealer. distribute oil. REPLACE SPARK PLUG Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 NOTE: For Canadian models only: This spark ignition system complies with the Canadian standard ICES-002. -
Página 8: Idle Speed Adjustment
2. Remove trimmer head by turning counterclockwise (looking from bottom of unit). 3. Thread replacement trimmer head onto the shaft by turning clockwise. Tighten until secure. STRAIGHT SHAFT MODELS 1. Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. -
Página 9: Fuel System
FUEL SYSTEM ENGINE Fuel stabilizer is an acceptable alternative in minimizing • Remove spark plug and pour 1 teaspoon of 50:1 2-cycle the formation of fuel gum deposits during storage. Add engine oil through the spark plug opening. Slowly pull stabilizer to the gasoline in the fuel tank or fuel storage the starter rope 8 to10 times to distribute oil. - Página 10 U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT IMPORTANT: This product is compliant with U.S. EPA Phase 3 regulations for exhaust and evaporative emissions. To ensure EPA Phase 3 compliance, we recommend using only genuine replacement parts. Use of non-compliant replacement parts is a violation of federal law.