M-system MKK-602 IX Manual De Utilización página 13

(Fig.3). In this way, any damage to the cooktop surface
is prevented.
Under no circumstances use abrasive sponges or irritat-
ing chemical detergents such as oven sprays or stain
removers.
USE AND FUNCTIONING OF THE MANUAL CONTROL
KNOBS.
USE
Use the control knobs to set the desired power. Turn
them clockwise to maximum.
In the case of plates with a double area, the external
heating element can be switched on starting from zero
and turning in an anticlockwise direction.
PILOT LIGHTS (fig. 4)
The pilot lights are ON when:
— at least one element is inserted; (fig. 4a)
— the top tenperature at the Indicated spot is higher
than 50°C (fig. 4b)
USE AND FUNCTIONING OF THE ELECTRONIC CONTROL
KNOBS
USE
Use the touch control system in the corresponding posi-
tion relative to the individual cooking needs. Keep in
mind that the higher the number, the more heat that it is
produced.
FUNCTIONING (Fig. 5-6)
- On the basis of the model you own, the appliance can
be switched on by actuating the start-up sensor (Fig. 5-
6 A). One zero will appear on all displays within10 seconds.
If no display is actuated within 10 seconds, the top will
switch off again.
- Press selection key F for the desired cooking area.
A luminous "0" will appear on the respective display with
a decimal point to indicate which cooking area is active.
- A hotplate may be switched on by activating the "+" or
"-" sensor within 10 seconds. If sensor D is used, the
display will show selection 9, while if sensor C is used,
the display shows selection 1 or 5, depending on the
model.
- Once this operation has been performed choose the
temperature adjustment with the "+" or "-" keys.
- The plate can be switched off by selecting "0" with the
D sensor, after 3 seconds the cooking area is
automatically switched off.
It is always possible to switch a plate off by touching the
"+" and "-" sensors at the same time.
- The cooking top can be switched off by touching the
main start-up sensor (Fig. 5-6 A). If all the plates are
selected on "0" the top will switch off after 10 seconds.
-If the top is equipped with plates with an extension (fig. 5-
6) switching on of the second area will be carried out after
having checked that :
- the key button LED (fig.5-6 B) is off, otherwise de-
insert it.
- Press the key (fig.5-6 A) to switch the top on.
- Choose the desired plate and adjust the power using
the "+" or "-" keys.
-Once the power has been adjusted choose the key
(fig.5-6 L) to activate the double area.
- To deactivate the double area check that the interested
plate has been selected (fig.5-6 F) and press the key
(fig.5-6 L) .
Note: the Double area function is activated only on plates
F1 and F2 (fig.5-6 ).
- If an object is placed above the controls, the cooking
top will automatically move to the OFF position.
When a plate is in the OFF position and the temperature
is higher than 50° there will be a luminous signal "H"
near to the respective selection key (Fig.5- 6 H).
- the B function blocks the functioning of the top on
selection. E.g.: if the function is activated while the top
has two areas switched on the programme remains
blocked even if you try to switch another area on. The
same thing happens if the appliance is switched off and
the function is activated; the top doesn't switch on.
To activate or deactivate it hold a finger on the B sensor
for about two seconds. The function is active when warning
light E is switched on.
Timer (Fig.6).
- Select the plate with the relative power.
- Press the selection key again of the already-activated
plate.
- Using the "+" and "-" keys set the desired time.
- The decimal point at the side of the power level will
indicate that the plate has the TIMER function activated.
- An acoustic signal will indicate switching off of the
cooking area.
FUNCTIONING (Fig.7)
Press the ON/OFF 11 button to switch on the cooktop.
For 10 seconds the display will show a dash. If no cooking
zone is switched on within 10 seconds, the hob will
automatically switch off.
To switch on the element you intend to use, press the
corresponding + or - button within 10 seconds. When the
+ button is pressed the display will show power level 9,
and when the - button is pressed it will show power level
4. After this operation, adjust the temperature with the +/
- buttons.
To switch off an element, press the - button until "0"
appears. The corresponding LED will switch off after 10
seconds.
You can also switch off an element by pressing
simultaneously the + and - buttons.
To switch off the hob, press the ON/OFF button 11. If all
of the elements are set to "0", the hob will witch off after
10 seconds.
If an object is placed on the hob control panel or any
liquid is spilt (water, milk, etc.) the hob will automatically
switch off and the 10 symbol will light up.
If the hob features double zone cooking elements, switch
on the second zone by pressing the corresponding 9-7
symbol for 3 seconds. After switching on the second
element, adjust the temperature with the +/- buttons.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING
THE ABOVE WARNINGS.
- 13 -