Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Technical specifi cations
Inputs
Band
Gain
Filters confi guration
No.
No. channels per fi lter
Nº
Slope adjustment
dB
Optimum input margin
Gain regulation
dB
Manual reg. gain
dB
Output level ***
Output level regulation
Noise fi gure
Rejection
dB
Input powering
(2)
V=
(automatic)
mA
Mains voltage/frequency
V~/Hz
Consumption
mA
Power
Max. working temperature
ºC
Protection index
(2) Total current available
Preamp. only
Only LNB
Preamp. + LNB
Troubleshooting
Channels are not adjusted to the programmed output level: Check that the
programmed fi lter for the highest output channel has both presence of signal
and the right level, since this value is taken as a reference for the adjustment of
the selected output level.
The channels entering through the input of BI/BIII (* BIII-VHF) are regulated
incorrectly: If we are entering only one channel through this input, its level
would be set 5dB below the UHF level channels. But if, with the same level, we
introduce several channels, the Avant will treat them like a higher-level single
channel, thus reducing the level adjusted of all of them regarding to the one it
would be obtained for just one channel.
If we need to amplify several channels coming from other processing units, we
recommend entering them on the input "Broadband (47-862 MHz)".
Channels in the broadband input are not equalised as regards fi lters:
The "broadband" input amplifi es signals coming from satellite receivers, the
recommended level for this input is between 70 and 74 dBμV (for UHF channels)
to get these channels equalised with the rest of the adjusted channels. If the
level applied is below the indicated range, these channels will have a lower level
than the rest; on the other hand, if the level is higher there will be disturbances
due to the intermodulation of channels.
(1) VHF inputs distribution for ref 532870: BI+FM & BIII
470 - 862
3).
10
0
0
9
0
1
7
2
1
6
3
1
5
3
2
0 - 5 **
0 - 9 **
60 - 105
0 - 20 *
± 9 (per fi lter)
120
96-111
20 (±16 MHz)
20 (±16 MHz)
20 (at 174 MHz)
24
60
W
150 mA
300 mA
300 mA
FM
BI+FM
(1)
(1)
87 - 108
47 - 68 / 174 - 230
47 - 110
(1)
174 - 260
(1)
Auto
Auto
(max. 44 ± 3)
---
---
---
---
---
---
---
---
---
---
---
---
---
---
60 - 85
62 - 87
± 9
± 9
120
120
2x 86-101
91-106
10
10
(1)
---
24
---
60
196 - 264 / 50-60
255
29
45
IP 20
*
Automatic adjustment (Depending on the wished level of exit and the
signal of entrance).
**
Programmable adjustment.
***
The output level depends on the nº of channels.
A high/low level detected in an input or a fi lter: The adjustment process
begins with the verifi cation of the signal levels introduced in the FM (BI+FM)
1
input and fi nally with the verifi cation of the programmed fi lters. The
indication that the FM (BI+FM)
the signal in these inputs will not aff ect the rest of the selected channels.
We must remember that level indications in FM (BI+FM)
fi lters shown on the programmer's display, are a reference for the adjustment
process, being the unit able to balance channels, where a level error has been
found, whenever input levels do not present large variations as regards the
maximum specifi ed range.
47 - 370
370 - 862
Auto
(max. 36 ± 2)
(max. 39 ± 2)
---
---
---
---
---
---
---
---
---
---
---
---
---
---
69 - 73
70-74
---
---
---
---
120
120
91-106
96-111
---
---
(1)
---
---
---
---
1
or BI/BIII (BIII)
1
level is low when we do not apply
11
IF SAT
950 - 2150
42 ± 2 - 45 ± 2
---
---
EN
---
---
---
---
0 - 12 **
---
---
123
---
9
40 (at 862 MHz)
13 / 17 (22 KHz)
300
1
,
1
1
inputs and
Publicidad
Tabla de contenido
