Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Tools and Parts
IMPORTANT:
■
Installer: Leave Installation Instructions with the homeowner.
■
Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector's use.
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
■
Cordless drill
■
■
Drill bits
■
■
Adjustable
■
wrenches (2)
■
■
Phillips screwdriver
■
■
Small level
■
■
Appliance dolly
■
Parts Needed
■
#8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)
■
2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)
■
Make custom panels or consult a qualified cabinetmaker or
carpenter to make the panels.
Overlay Series: Make custom panels, or consult a qualified
cabinetmaker or carpenter to make the panels. See "Overlay
Series Custom Panels and Handle Kits" for more information.
Stainless is shipped complete.
■
If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
¹⁄₄" (6.35 mm) compression fitting.
Location Requirements
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT:
■
Observe all governing codes and ordinances.
†®TORX is a registered trademark of Acument Intellectual Properties, LLC
INSTALLATION REQUIREMENTS
Torx
®†
T27 screwdriver
¹¹⁄₃₂" nut driver
³⁄₈" and ¹⁄₂" open-end wrenches
⁵⁄₃₂" hex key
¹⁄₄" and ⁵⁄₁₆" socket drivers
Tape measure
Utility knife
■
It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.
■
Do not install in a location where the temperature will fall
below 55°F (13°C).
■
Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
■
Ceiling height must allow for side tipping radius. See "Tipping
Radius."
■
Location should permit door to open fully. See "Door Swing
Dimensions."
■
Location must permit top grille removal. See "Opening
Dimensions."
Opening Dimensions
■
To avoid tipping during use, the solid soffit must be within 1"
(2.5 cm) maximum above the refrigerator. If the solid soffit is
higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the
rear wall studs so that the bottom of the anti-tip board is 84"
(213.4 cm) from the floor. See "Install Anti-Tip Boards" for
more information.
NOTES:
A clearance of ¹⁄₂" (1.3 cm) must be maintained above the
■
top grille in order for the top grille to be removed.
■
Do not remove the foam gasket on top of the compressor
cover unless removal is necessary to fit the unit under a
soffit. Removal of the gasket will cause loss in cooling
efficiency.
■
If installing under a solid soffit, after installation raise the
leveling legs so that the gasket is pressed snugly against
the soffit.
A
B
A. Gasket
B. Compressor cover
■
A grounded 3 prong electrical outlet should be located within
a specified number of inches from the right-hand side
cabinets or end panel. See the chart following the graphic for
the number of inches required for your model. For more
information, see "Electrical Requirements."
¹⁄₂
"
(1,3 cm)
5 5 5 5 5 5
Publicidad
Tabla de contenido
