Publicidad
Idiomas disponibles
Idiomas disponibles
When charging:
Blue: Battery is in a fully charged state.
Blue (flashing): Battery is in a high partially charged state.
Purple (flashing): Battery is in a low partially charged state.
Red (flashing): Battery needs to be recharged.
Blue & Red (flashing alternately): The battery of the Light Panel is overheated due to extensive use or recharging. The charging
process will stop at this stage and will automatically resume after a cool down period.
When operating:
Blue: Battery is operating at full voltage.
Purple: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged.
Red (Flashing): Battery is operating at extremely low voltage. The built-in low voltage protection has activated and the unit will
automatically shut down. The unit must be recharged immediately.
Blue & Red (flashing alternately): The battery of the Light Panel is overheated due to extensive use or recharging. The
operation will stop at this stage and will automatically resume after a cool down period.
CHARGING/RECHARGING THE LIGHT
The three light panels are shipped in a partially charged state. They must be charged after purchase and BEFORE first use. Using the
120 Volt AC Charging Adapter, charge up to three light panels together through the DC Charging Port at the bottom of the Light
Head Assembly Base OR charge individual light panels through the DC Charging Port on the bottom of each light panel. Charge for
4 hours or until the Battery/Charge Status LED Indicator lights blue.
Recharge after each use until the Battery/Charge Status LED Indicator lights blue.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least every 3 to 6 months.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Never place a light panel face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
Charging/Recharging Through the Light Head Assembly Base
This charging method allows simultaneous charging of up to three Light Panels at a time through the DC Charging Port under the
Light Head Assembly Base (refer to the "Features" section to locate).
1. Make sure all the Light Panels are turned off and properly attached to the Light Panel Holders.
2. Plug the 120V AC Charging Adapter into a (powered) standard North American 120 volt 60Hz outlet. The Power Indicator on
the 120V AC Charging Adapter will light red to indicate the charger is plugged in and ready.
3. Insert the barrel tip of the AC Charging Adapter into the DC Charging Port under the Light Head Assembly Base.
4. When the AC Charging Adapter is properly connected, the Battery/Charging Status LED Indicator on the front of the each Light
Panel will light or flash in one of three colors (as described in the "Reading the Battery/Charge Status LED" section) to indicate
the battery charging status.
5. Charge until the Battery/Charge Status LED Indicator lights blue.
Charging/Recharging Individual Light Panels
This charging method allows charging of an individual Light Panel through the DC Charging Port located on the bottom of the Light
Panel (refer to the "Features" section to locate).
1. Make sure the light panel is turned off.
2. Plug the 120V AC Charging Adapter into a (powered) standard North American 120 volt 60Hz outlet. The Power Indicator on
the 120V AC Charging Adapter will light red to indicate the charger is plugged in and ready.
3. Connect the barrel tip of the AC Charging Adapter to the DC Charging Port located on the base of the Light Panel.
4. The battery and charging status LED indicator on the front of the Light Panel will light or flash in one of three colors (as
described in the "Reading the Battery/Charge Status LED" section) to indicate the battery charging status.
5. Charge until the Battery/Charge Status LED Indicator lights blue.
TPL45S_ManualENSP_022414.indd 16-17
16
OPERATING INSTRUCTIONS
Operating the Light Panels Cordless
Configure the Tripod Light as desired (refer to the "Configuring the Tripod Light" section).
Locate the Light Mode Button on the front of each Light Panel you wish to use.
• Press once for high intensity.
• Press again for low intensity.
• Press a third time for to turn the light off.
• Press and hold the Light Mode Button for about five seconds for flashing LEDs and again about five seconds to return back to
previous operating intensity.
Note:
During operation, the Battery/Charge Status LED Indicator will light in one of three colors (as described in the "Reading the Battery/Charge Status LED"
section) to indicate the battery status.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
Do not shake the tripod light and do not attach anything additional to the tripod light or its components or risk of breakage may
occur.
Operating Light Panels Corded
• Attach the AC Charging Adapter as described in the "Charging/Recharging the Light" section.
• Operate the unit as outlined in the previous section.
Using the Carry Strap
The carry strap may be used to carry the unit. Attach the Carry Strap to the Carry Strap Fastener and the Center Lock and adjust the
slide on the cords to keep the lanyard secure around any supporting object.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• Use the Carry Strap for hand-carrying this light only. It is not intended for hanging the tripod light during use or storage.
• The Carry Strap is not intended to support additional weight. Do not attach or hang anything additional to the tripod light while
hand-carrying it using this strap or risk of breakage may occur.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 3 to 6 months.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the light unit with a soft cloth moistened with a
mild solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to
replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to the
number of recharge cycles, proper care and maintenance of the battery by the end user, and environmental conditions. Contact
manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of properly. Recycling is required. Failure to comply with local,
state and federal regulations can result in fines, or imprisonment. Contact your local waste management authority
to dispose of this product.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
• TROUBLESHOOTING
The battery/charge status LED indicator does not light when charging
1. Check connection to the DC Charging Port (either at the bottom of the Light Head Assembly Base or on the bottom of each
Light Panel).
2. Check connection to the AC power source.
PLEASE
RECYCLE
17
2/24/2014 7:56:31 PM
Publicidad
