Cycle Programming; Automated System Test - Genius JA383 Instrucciones Para El Uso

ENGLISH
Display Function
CLOSING PHOTOCELLS LOGIC:
Select the tripping mode of the closing
photocells.
They operate for the closing movement
only: they stop movement and reverse it
when they are released, or they reverse it
immediately.
= Reverse on release
= Reverse immediately when opening
OPENING PHOTOCELLS LOGIC:
Select the tripping mode of the opening
photocells.
They operate for the opening movement
only: they stop the movement and restart
it when they are released, or they reverse it
immediately.
= Reverse immediately when closing
= Restart movement on release
ENCODER:
If the encoder (optional) is used, you may
select its presence.
If the encoder is present and enabled,
"decelerations" and "partial opening" are
controlled by the encoder (see relevant
paragraphs).
The encoder operates as an anti-crushing
device: If the gate strikes an obstacle during
opening or closing,
immediately reverses gate leaf movement
for 2 seconds.
again during the 2-seconds reversing time,
it STOPS movement without commanding
any reversing.
= Encoder enabled
= Encoder disabled
DECELERATIONS:
You can select gate deceleration after the
opening and closing limit-switches have
been tripped.
Time can be adjusted from
sec. in 0.04-second steps.
The maximum value of
about 7 cm.
If an encoder (optional) is used, the
adjustment is not determined by time but
by motor revs, thus obtaining greater
deceleration precision.
= Deceleration disabled
from to
PARTIAL OPENING:
You can adjust the width of leaf partial
opening.
Time can be adjusted from
sec. in 0.1-second steps.
If an encoder (optional) is used, the
adjustment is not determined by time but
by motor revs, thus obtaining greater
precision of partial opening.
E.g. for a gate with a sliding speed of 10 m
/min, value
metres of opening.
E.g. for a gate with a sliding speed of 12 m
/min, value
metres of opening.
the encoder
If the encoder operates
to
corresponds to
= Deceleration enabled
to
corresponds to about 1.7
corresponds to about 2
Default
Display
WORK TIME:
We advise you to set a value of 5 to 10
seconds over the time taken by the gate to
travel from the closing limit-switch to the
opening limit-switch and vice versa. This will
protect the motor against any overheating
if a limit-switch fails.
Adjustable from
second steps.
Subsequently, viewing changes to minutes
and tens of seconds (separated by a point)
and time is adjusted in 10 second steps, up
to a maximum value of
E.g. if the display shows
min. and 50 sec.
ASSISTANCE REQUEST (combined with next
function):
If activated, at the end of countdown
(settable with the next function i.e. "Cycle
programming") it effects 2 sec. of pre-flashing
at every Open pulse (job request). Can be
useful for setting scheduled maintenance
jobs.

CYCLE PROGRAMMING:

For setting countdown of system operation
cycles. Settable (in thousands) from
to
The displayed value is updated as cycles
proceed.
This function can be used to check use of
the board or to exploit the "Assistance
request".
GATE STATUS:
Exit from programming and return to gate
status viewing (see Chpt 5.1.).
6. START-UP
6.1. INPUTS CHECK
The table below shows the status of the LEDs in relation to to the
status of the inputs.
Note the following:
Check the status of the LEDs as per Table.
Operation of the signalling status LEDs
LEDS
FCA
FCC
OPEN B
OPEN A
FSW OP
FSW CL
STOP
EDGE
NB.: The status of the LEDs while the gate is closed at rest are shown in bold.
7.

AUTOMATED SYSTEM TEST

When you have finished programming, check if the system is
operating correctly.
Most important of all, check if the force is adequately adjusted
and if the safety devices are operating correctly.
14
Function
to sec. sec. in one-
, work time is 2
= Active
= Disabled
thousand cycles.
L = closed contact
ED LIGHTED
L = open contact
ED OFF
LIGHTED
Limit-switch free
Limit-switch free
Command activated
Command activated
Safety devices disengaged
Safety devices disengaged
Command inactive
Safety devices disengaged
Default
minutes.
OFF
Limit-switch engaged
Limit-switch engaged
Command inactive
Command inactive
Safety devices engaged
Safety devices engaged
Command activated
Safety devices engaged