KBS Delicious Manual De Instrucciones página 10

REGOLAZIONE E PULIZIA
WARNINGS
It is most important that this instruction booklet is kept together with the appliance both for future reference and for
reasons of safety. 1 . Adults should operate this appliance only. Do not allow children to use the controls or play with it.
2 . It is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical installation of
the appliance should be carried out by a qualified electrician or other competent person. . Never attempt to carry out repairs
unassisted. Inexpert repairs can cause serious damage and malfunction. . Assistance has to be provided by an authorized
engineer only. Always use original spare parts. . This appliance is not suitable for the storage of basic commodities not
7
including food-stuffs. . The manufacturers of this appliance accept no responsibility for the consequences of misuse in
contravention of these safety instructions. It further reserves the right to carry out improvements without prior notice. 8
installing the cabinet directly in line with sunlight. . Nevere install the appliance near sources of heat, such as radiators,
stoves, etc. 10 . Keep the ventilation grills free from obstruction for at least 30 cm.
the shelves and grills do not hang over the edges.
evaporator, we recommend stopping the compressor and placing the goods in special refrigerated containers, kept at the same
temperature, until defrosting is completed;if this is not carried out the compressor will continue to operate leading to a
wasteful consumption of electricity and poor performance.
to keep the door open at least 10 cm.
1. WHEEL-BASE PLATE INSTALLATION (OPTIONAL)
The appliance is equipped with a wheeled-base plate to move it easily.
under the 4 bars used as feet.
3.
Fit the cross bar at the bottom of the 4 feet firmly tightening the 4 nuts with a wrench.
is correctly mounted and bears vertical efforts before installing the appliance on it (See picture 1).
2. UNPACKING INSTRUCTIONS
CARDBOARD PACKAGING 1a
1b. Remove the nails from the wooden crate with care
3 . Two operators have to hold and lift the appliance. They will have to put it onto the trolley already assembled. The holes on
the lower part of the tank have to match with the trolley's holes. . Using a wrench, screw the screws, found in the envelope in
the tank, onto these holes. 5.
inside the packaging before disposal. . Separate the packaging materials to facilitate disposal (See picture 2).
3. INSTALLING THE GLASS PROTECTION COVER
ALL MODELS: 1. Unpack the glass panes stored inside the tank and on the shelf.
the flank. Tighten the lock screw. . Repeat the operation for the other side. . Install the front glass by inserting it in the
relevant groove along the edge of the front frame. . Fasten the front glass to the sides using the relevant angle hooks, place
the plastic washer between screw and glass. Straight glasses
the front glass, and then fixing it to the angle hooks, always placing the plastic washer between screw and glass. Straight
glasses and Bent glasses ONLY: 7.
screws. Place the plastic washer between screw and glass
then, push the extra wire from inside the tank to the internal part of the appliance.
Place the plastic washer between screw and glass.
4. THE SLIDING PANELS
Using the two sliding panels, the back part of the dome can be closed, for hygienic reasons, whilst working, protecting it from
dust and insects. 1. Insert the lower sliding panel into the inner guide (below) and place it on the edge of the lamp (above).
2. Insert the other sliding panel into the outer guide. . Make the two panels slide to their stops, keeping the two holes at the
ends. (See picture 4)
5. CLEANING THE INTERNAL TANK
1 . Remove the protection film from the stainless steel of the tank sides and of the other elements.
soft sponge and neutral detergents. . Dry with a soft cloth.
6. CLEANING THE COVER AND EXTERNAL CLEANING
1. Remove the protective film from the stainless steel. . To clean use the same products used for the inside.
transparent glasses of the sliding panels and the lamp opal glass protection, avoiding the use of substances containing alcohol
or other solvents which would damage them. Only use a soft sponge damped with water.
6
9
12 . If damp air or products to be refrigerated should cause ice to form on the
14. Our products are for internal use only do not install outside restaurants, shops.
2. Insert the black cap in the holes on top of the 4 feet, with the bevel turned towards the bolt.
. Cut the strip. Remove the cardboard packaging by sliding upwards.
. 2.
Make sure that the appliance is placed onto a flat, level surface. . Make sure there is nothing left
7
3
5
Install the upper lamp-holder, fixing it to the sides and to the roof with the supplied
10. Place the shelf on the relevant supports, just secured (See picture 3).
- ALL MODELS, SS excluded
3
3
2
5
11
13
. If the appliance is not working and unused, it is indispensable
1. Fit the 4 wheels with the relative rings, in the holes
Take glass panes and envelopes out of the tank and the shelf.
4
2.
4
ONLY: 6
. Install the top glass placing it upon the sides and on
. 8. Place the aluminium pipe in the position shown in the picture;
9.
9
3
4
. Ensure that the products displayed on
4.
Make sure that the whole structure
WOODEN CRATE
6
Insert a glass-side in the tank, against
Fit the shelf supports on the glass sides.
2. Only clean the tank with a
3. Clean the
GB
. Avoid