Power Requirements; Troubleshooting - Altec Lansing VS4121 Guia Del Usuario

System Specifications
Power rating conforms to FTC Amplifier Rule #16 C.F.R. Part 432.
Sound Pressure Level (SPL): 97 dB
Total Continuous Power: 31 Watts RMS
Front Speakers: 6 Watts/channel @ 4 ohms @ 10% THD @ 150 -
20000 Hz 2 Channels Loaded
Subwoofer: 19 Watts @ 4 ohms @ 10% THD @ 20 – 150 Hz Single
Channel Loaded
System Response: 25 Hz – 15 kHz (-10dB)
Signal to Noise Ratio @ 1 kHz input: > 73 dB
SATELLITE AMPLIFIED SPEAKERS
Drivers (per satellite):

Troubleshooting

Symptom Possible Problem
LED is not lit. Power isn't turned on.
AC cord isn't connected to the wall outlet.
Surge protector (if used) isn't powered on.
Wall outlet not functioning.
No sound from Power isn't turned on.
one or more
speakers.
Volume is set too low.
Audio cable isn't connected to audio source.
Audio cable is connected to wrong output on
audio source.
Problem with audio source.
Crackling sound Bad connection.
from speakers.
Volume control in Windows is set too high.
A problem with your audio source.
Sound is Volume level set too high.
distorted.
Windows volume control is set too high.
Sound source is distorted.
Two 28mm microdrivers
One 3" mid-range
Altec Lansing's superior sound comes from our proprietary technology,
which utilizes custom-built, high-fidelity drivers, state-of-the-art
equalization circuitry, and a harmonious mix of the following
specifications:
SUBWOOFER
Driver:

POWER REQUIREMENTS

USA, Canada:
Europe, United Kingdom,
applicable Asian countries:
UL/cUL/CE/NOM Approved
Solution
Press Power button on right satellite.
Check to see if the power on LED is illuminated on the right satellite. If not,
connect AC power.
If the subwoofer's AC power cord is plugged into a surge protector, make sure
the surge protector is switched on.
Plug another device into the wall outlet (same jack) to confirm the outlet
is working.
Verify the subwoofer's AC power cord is plugged into the wall outlet.
Verify the Power button has been pressed by confirming the LED
is illuminated.
Turn the volume knob clockwise to raise the volume.
Check volume level on the computer sound card or alternate audio source
device and set at mid-level.
Connect audio cable to the audio source. Make sure the signal cable is
inserted firmly into the correct jack.
Make sure the lime green 3.5 mm audio input cable is connected and fully
inserted into the "line-out" or "audio-out" jack on your soundcard or other
audio source.
Test the speakers on another audio source by removing the lime green 3.5mm
audio input cable from the audio source and connecting it to the "line-out"
or headphone jack of a different audio source (e.g., Walkman, Discman or
FM radio).
Check all cables. Make sure they are connected to "line-out" or "audio-out"
jack on your sound card or other audio source—and NOT "speaker-out."
Check the Windows volume control and decrease if necessary.
Unplug the lime green 3.5 mm audio input cable from the audio source. Then
plug it into the headphone jack of an alternate source (e.g., portable CD,
cassette player or FM radio).
Decrease volume level.
Adjust the Windows volume and balance controls to the center as a starting
point, then use the speaker controller to adjust as necessary.
.WAV and .MID files are often of poor quality; therefore distortion and noise
are easily noticed with high-powered speakers. Try a different audio source
such as a music CD.
3
1
One 6 ⁄ " long-throw woofer
2
120 V AC @ 60 Hz
230 V AC @ 50 Hz