Cequent Performance Products T-One T-Connector Instrucciones De Instalación

Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One T-Connector
®
T-One connecteur en T
®
T-One Conector en T
®
Buick Regal
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l'installation. Durant
l'installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
118639-037 Rev. A
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32" Drill Bit),
1/4" Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open the tailgate to remove the vehicle's
taillight housing assemblies. On the driver's side,
inside the vehicle behind the taillights, remove
plastic cover and pull back insulation liner to access
the plastic wing nut holding the taillight in place
de . Unscrew the plastic wing nut and carefully
pry the vehicle taillight housing assembly away
from the vehicle, being careful not to break the
alignment tabs. Carefully separate the vehicle's
plugs. Repeat this step for the vehicle's
passenger's side taillight assembly.
2. On both the driver's and passenger's side,
slit the grommet to allow for the T-One
T-Connector's wiring f . Route the T-One
T-Connector ends containing the yellow and
the brown wires through the hole and into
the tail lamp pocket and reseat the grommet
around the wires. Leaving the 4-Flat and black
convertor box in the cargo area.
3. Insert the T-One T-Connector end, with the
®
yellow wire, between the vehicle wiring connectors
and lock into place.
WARNING
All connector surfaces should be clean and free
of dirt. Be careful not to damage the locking tabs
and be sure that connectors are fully inserted with
locking tabs in place.
d
e
6/25/2014
f
4. Route the T-One
green wire below the threshold cover to the
passenger's side taillight housing. Repeat steps 2
and 3 using the T-One
containing the green and red wires.
NOTE
Route the 4-Flat through the driver's side trim
panel into side storage compartment and store
there when not in use.
WARNING
Be careful not to pinch harness in trunk latch.
5. On driver's side, locate a flat surface in a out of
the way place and mount the T-One
black convertor box with the double sided tape.
6. Locate a suitable grounding point. Drill a 3/32" hole
and secure the white wire using the eyelet and screw
provided. Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to drilling to
®
avoid damage to the vehicle and/ or personal injury.
®
Do not drill into any exposed surfaces.
7. On the driver's side, locate the red 12 ga. power
wire from the T-One
black 12 ga. wire provided.
8. Either route the black wire thru a grommet and
along the exterior frame or follow the existing
wiring along the thresholds into the engine
compartment up to the battery avoiding areas
that may pinch or break the wire g .
WARNING
If routing the wire thru a grommet and along the
exterior of the vehicle, be careful to avoid any hot
pipes, heat shields, the fuel tank or any other points
that may pinch or break the wire.
T-Connector containing the
®
T-Connector ends
®
T-Connector's
®
T-Connector box. Attach the
®
PAGE 1 OF 3
g
h
i
9. Disconnect the vehicle's Negative (-) battery cable.
If not removed, remove the fuse from the yellow
fuse holder (provided). After cutting the fuse holder
wire h , attach the ring terminal and secure to the
vehicle's Positive (+) battery cable i . Connect the
other end of the fuse holder to the black 12 ga. wire,
using the yellow butt connector (provided).
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle's battery.
10. Reconnect the vehicle's Negative (-) battery cable
and install the 10 amp fuse into the fuse holder
from Step 9.
WARNING
All connections must be complete for the T-One
T-Connector to function properly. Test and verify
installation with a test light or trailer once installed.
For initial test, reset vehicle electrical system by
temporarily removing the key from the ignition.
11. Secure the remainder of the T-One
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
12. Reinstall the plastic trim panels, threshold,
storage covers, floor covering and other items
removed during installation, being careful not
to pinch or cut the wires.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle's owners manual &
instruction sheet for additional information.
®
T-Connector
®