Cequent Performance Products T-One Instrucciones De Instalación

Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One T-Connector
®
T-One connecteur en T
®
T-One Conector en T
®
ACURA ILX
WARNING
ALWAYS read and follow all warnings and
instructions included with purchase before
beginning installation. Keep for future reference.
DO NOT exceed lower of towing manufacturing
rating (including in your vehicle owner's manual)
or specific amperage ratings stated on product.
ALWAYS read, understand and follow all
warnings and instructions printed on tow
vehicle's battery.
ALWAYS wear safety glasses and use all safety
precautions during installation.
118627-037 Rev. B
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32" Drill Bit),
Wire Crimpers, Wire Cutters, Test-probe, Utility Knife
1. Open the rear tailgate to access the bolts that hold
the taillights in place. Remove the taillights on both
the driver and passenger side of the vehicle. Remove
threshold, trunk floor panels and trays
Set aside all items removed being careful not to
damage parts.
2. Partially remove the corner felt trunk liner,
on both sides, exposing the vehicle's taillight
D
wiring harness .
3. On both the driver's and passenger's side, pull
the vehicle taillight wire harness and unseat the
grommet. On both the driver's and passenger's side,
slit the grommet to allow for T-One
EF
wiring .
4. From inside the trunk, route the T-One
ends with yellow, brown and red wires thru the
grommet on the driver's side.
5. On the driver's side, attach two (2) sets of
connectors from the T-One T-Connector, one
®
containing yellow wires and the other containing
brown and red wires, in between the vehicle
taillight wiring harness connectors. Seat the
g
grommet in opening .
A
B
6/13/2016
C
6. Repeat steps 4 & 5 on passenger's side with T-One
T-Connector end containing the green wire.
WARNING
All connector surfaces should be clean and free
of dirt. Be careful not to damage the locking tabs and
be sure that connectors are fully inserted with locking
tabs in place.
7. Locate a suitable grounding point near the connector
inside the vehicle. Clean dirt and rustproofing from
abc
.
the area. Drill a 3/32" hole and secure the white wire
using the eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to drilling to
avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.
8. Locate a flat surface in an out of the way place and
mount the T-One
to prevent damage or rattling.
T-Connector's
®
9. From inside the vehicle, connect the black 12 ga.
wire and the red wire from the T-One
T-Connector
®
black box with the supplied yellow butt connector.
Either route the black wire thru a grommet and along
the exterior frame or follow the existing wiring along
the thresholds into the engine compartment up to the
battery avoiding areas that may pinch or break the
h
wire .
WARNING
If routing the wire thru a grommet and along the
exterior of the vehicle, be careful to avoid any hot
pipes, heat shields, the fuel tank or any other points
that may pinch or break the wire.
C D
®
T-Connector's black box-module,
®
T-Connector
®
PAGE 1 OF 3
F G
H
I
J
10. Disconnect the vehicle's negative (-) battery cable. If
not removed, remove the fuse from the yellow fuse
holder (provided). After cutting the fuse holder wire
i
, attach the ring terminal and secure to the vehicle's
j
Positive (+) battery cable . Connect the other end
of the fuse holder to the black 12 ga. wire, using the
yellow butt connector (provided).
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle's battery. All connections must
be complete for the T-One T-Connector to function
®
properly. Test and verify installation with a test light
or trailer once installed. For initial test, reset vehicle
electrical system by temporarily removing the key
from the ignition.
11. Secure the remainder of the T-One
ness with the cable ties provided, to prevent damage
or rattling and being careful to avoid any areas that
would pinch, cut or melt the wire.
12. Reinstall the plastic trim panels, threshold, storage
covers, floor covering and other items that may have
been removed during installation, being careful not to
pinch or cut the wires
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuits can cause fires. DO NOT exceed
stated product ratings. Read vehicle's owner's manual
& instruction sheet for additional information.
T-Connector har-
®