Accessing The Service Menu; Confi Rming Service Adjustment Changes; White Balance Adjustments; Picture Quality Adjustments - Sony TRINITRON KV-29FA350 Manual Del Usuario

3-2. ACCESSING THE SERVICE MENU

Use the remote commander to access the service menu and perform the
following adjusments.
1. Standby mode (Power off).
2. Press the following buttons on the remote commander within a
second of each other:
DISPLAY
Channel
The screen displays the fi rst service data category item.
Item # Data value
Categoy Item
On the Remote Commander press 2 to select the next category, or
1.
5 to select the previous category.
Press 1 to select the next item, or 4 to select the previous item.
2.
Press 3 to increase the data value, or 6 to decrease the data
3.
value.
Press MUTING then 0 to write into memory.
4.
GEOM 000 HPOS
Write with [MUTING].
"WRITE" displays when saving changes
GEOM 000 HPOS
Write executed with -.
GEOM 000 HPOS
Resetting the User Menus
Use the following procedure to reset the User Menus to the factory default
settings.
1. Access Service Menu.
Press 8 then 0 on the Remote Commander.
2.
KV-29FA350/29FA750
POWER
+
5
Sound Volume
Video Input Name
GREEN
028 SERVICE 60 VIDEO 1
GREEN
028 WRITE 60 VIDEO 1
"WRITE" becomes red when saving,
then changes to "SERVICE"
RED
028 WRITE 60 VIDEO 1
3-3. CONFIRMING SERVICE ADJUSTMENT
CHANGES
1. After completing adjustments, pull out the plug from the AC outlet,
then replace the plug in the AC outlet again.
2. Access Service Menu.
3. Using the buttons on the Remote Commander, locate the adjusted
items again to confi rm they were adjusted.

3-4. WHITE BALANCE ADJUSTMENTS

NOTE: FOCUS adjustment should be completed before White Balance
adjustment. (See 2-3. FOCUS ADJUSTMENT)
1. Access Service Menu.
2. Input white raster signal using signal generator.
3. Set the following condition:
Picture "STANDARD", PICT 006, note value of "WTS"
then change to 00.
Press 2 or 5 to select the WHBL category.
4.
Press 1 or 4 to display the 03 "GDRV" and 04 "BDRV" items.
5.
Press 3 or 6 to adjust for the best white balance.
6.
7. At Cutoff, select WHBL 000 "BKOR" and 001 "BKOG" and adjust
the data.
8. Perform adjustment at Highlight and Cutoff condition until it reaches
its target.
9. Press MUTING then ENTER to save into the memory.
10. Set PICT 006 "WTS" back to its original data.

3-5. PICTURE QUALITY ADJUSTMENTS

P Max/Contrast Adjustment
1. Set TV to Video mode.
2. Set Picture mode to "CUSTOM".
3. Input PAL 100% Color Bar (CB) to TV set (OTHER model)
NTSC 75% Color Bar (CB) (NTSC model).
4. Set the following condition:
PICTURE 100%, COLOR 0%, BRIGHTNESS 50%
5. Connect an oscilloscope to pin
6. Access the Service Menu. Set PICT 003 "PWL" to 00h and WHBL
017 "BLBG" to 01h.
Press 1 or 4 to display SADJ 000 "PMAX", then adjust VR by
7.
pressing 3 or 6 until the spec below is displayed:
PAL
VR
8. Copy the adjusted PMAX data to TV mode.
KV-29FA350/29FA750
4
(R Output) of CN004.
VR
Black
NTCS
1.61 0.03Vpp
18