Safety Codes And Standards; Grounding Instructions; Clearances And Dimensions - Bosch HMD8451UC Instrucciones De Instalación

Safety Codes and
Standards
This appliance complies with the latest version of one or
more of the following standards:
• CAN/CSA C22.2 No. 61 - Household Cooking Ranges
• UL 858 - Household Electric Ranges
• CAN/CSA C22.2 No. 150 - Microwave Ovens
• UL 923 - Microwave Cooking Appliances
• UL 507 - Electric Fans
• CAN/CSA C22.2 No. 113 - Fans and Ventilators
• CSA C22.2 No. 64 - Household Cooking and Liquid-Heating
Appliances
• UL 1026 - Electric Household Cooking and Food Serving
Appliances
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards apply
to specific installations.

Grounding Instructions

This appliance must be grounded. In the event of an elec-
trical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding
wire with grounding plug. The plug must be plugged into a
outlet that is properly installed and grounded.
WARNING
Improper use of the grounding can result in a risk of
electric shock.
Consult a qualified electrician or serviceman if the ground-
ing instructions are not completely understood, or if doubt
exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the appliance.
The installer must perform a ground continuity check on
the power outlet box before beginning the installation to
insure that the outlet box is properly grounded. If not prop-
erly grounded, or if the outlet box does not meet Electrical
Requirements, a qualified electrician should be employed
to correct any deficiences.
English 3
Clearances and
Dimensions
• For safety considerations, do not install Drawer
Microwave in any combustible cabinetry which is not
in accord with the stated clearances and dimensions
in the "Drawer Microwave Measurements" section
following. See Figure 3 (standard installation) or Figure
4 (flush installation).
• Dimensions that are shown in Figure 3 (standard installa-
tion) or Figure 4 (flush installation) must be used. Given
dimensions provide minimum clearance. Locate electrical
outlet in the shaded area in the upper left-hand corner of the
cutout. See Figure 6.
• Supporting surface must be solid and level. Pay special
attention to the floor of the cabinet opening on which the
Drawer Microwave will sit. The floor of the opening should
be constructed of plywood strong enough to support the
weight of the oven (about 100 pounds).
• Check the location where the Drawer Microwave will be
installed for proper electrical supply.
• Your oven can be built into a cabinet or wall as a stand-
alone unit or under a built-in gas or electric wall oven and
the followings:
GAS ELECTRIC
COOKTOPS COOKTOPS
NGM5055UC NEM5066UC
NGM5655UC NET8066UC
NGM8055UC NET8066SUC
NGM8065UC NETP066SUC
NGM8655UC NEM5666UC
NGM8665UC NET8666UC
NGMP055UC NET8666SUC
NGMP655UC NETP666SUC
• Check to be sure that there is a clearance of 2 inches or
greater between the top of the Drawer Microwave unit and
the bottom of a built-in wall oven above it.
• The microwave interior will easily accommodate a 9" x 13"
oblong dish or a bag of microwave popcorn.
INDUCTION
COOKTOPS
NIT5066UC
NIT8066UC
NIT8066SUC
NITP066UC
NITP066SUC
NIT5666UC
NIT8666UC
NIT8666SUC
NITP666UC
NITP666SUC