Descargar Imprimir esta página

Craftsman 919.762500 Manual Del Operador página 11

Publicidad

Idiomas disponibles

Idiomas disponibles

When engine starts, g radually m ove choke lever t o
RUN position.
}fengine doesnotstartafter5 pu_ls, piace choke
backtorunposition.
For hot engine starts make sure choke/run }ever is in
the run position, Make sure fue_ shut off valve is open
and throttie is in the Rabitt position.
NOTE: If any leaks are present shut unit down and
tighten fittings.
How To Use Yeur
Pressure
Washer
On the end of your spray gun is a nozzle that you can
twist from side to side, With the adjustable nozzle you
can adjust the nozzie to either high pressure or Iow
pressure.
Turn the nozzle in a counter
clockwise
direction
to
achieve
low pressure.
Turn nozzie clockwise
for high
pressure.
For most effective
cleaning,
keep spray nozzie
between
8 and 24 inches of cleaning
sudaceo
iMPORTANT:
If you get spray nozzle too close,
especially
on high pressure,
you may damage
the
cleaning su.dace.
The pressure
control
knob is located on the pump.
You can increase
the pressure
by turning
the knob
ciockw_se
or decrease
the pressure
by turning the
knob counterclockwise.
/ rIq
_,', ", /
_08
:: ' /_ _-._,.,_
.........
._\ '.,
'-,
,.
\ i : .j ...,,
x%
, ,
NOTE; The maximum
pressure
for the unit is set at its
maximum
setting
at the factory.
Do not attempt
Io adjust
the pressure
higher than this factory setting.
t_siasg Soaps/Chemicals
IMPORTANT;
Use soaps and chemicals
that are designed
specifically
for use with pressure
washers.
To apply soap/
chemicals
follow these steps:
Prepare
the soapichemica_
as required
by your job.
Insert soapichemicai
line into your container
(soap/
chemicals
not inc!uded).
NOT_;
The first step involves
applying
an appropriate
soap/chemical
solution
to penetrate
and loosen grime.
The soap/chemica!
is appIied
at iow pressure
to avoid
splashing,
over spray and waste.
Leave the solution
on surface
for 3 to 5 minutes
to atiow solution
to work.
NOTE: The second
step involves
cleaning
the surface
you have prepared
with the pressure
washer
and then
rinsing it clean.
Turn the adjustable
nozzie counter
c;ockwise
to low
pressure
mode. Soap/chemicais
cannot
be applied
with nozzle in high pressure
position.
o Review the use of the adjustable r;oxz e.
o Connect
garden hose to water infer (see "To Start "_,<our
Pressure
Washer"),
check that high p_{:-ss_.._re h ose is
connected
to spray gun and pump (s.i _ Assembly},
and start engine.
o AppIy soap/chemicals
to dry surfac
.'.string from the
bottom
and working
up.
o Al!ow the soap/chemicals
to soak i_ b : :,,een 3-5
minutes
before washing
and rinsing?;.
For cleaning,
start at iower portion
(::i }:_
to be
washed
and work upward_ using !o;:
::.en over.-
iapping strokes.
Your pressure
washer is equipped
with a (;isemicaI
injector adjustment
knob.
With the k_u._b_uily opened
you will get maximum
chemical
draw.
With knob fui_y
ciosedyouwiilgetnocbernicaidraw.
r knob_n
counter
clockwise
direction
to achieve
_(re
chemica_
draw and clockwise
for less chemicai
d_"_w.
/
//
;/i/
After using the p_essure washer, it is recommended
the pump,
chemical
iniector
and chemical
!ire be
flushed with clear wate._: To do so. simply
place
chemical
injector
hose in water
arsd siphon
for I to 2
minutes.
11

Publicidad

loading