General Remarks Regarding The Ce Marking - Hameg Instruments HM 8123 Manual Del Usario

G e n e r a l i n f o r m a t i o n r e g a r d i n g t h e C E m a r k i n g
KONFORMITÄTSERKLÄRUNG
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE
DECLARACIóN DE CONFORMIDAD
Hersteller / Manufacturer / Fabricant / Fabricante:
HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen
Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt
The HAMEG Instruments GmbH herewith declares conformity of the product
HAMEG Instruments GmbH déclare la conformite du produit
HAMEG Instruments GmbH certifica la conformidad para el producto
Bezeichnung: Universal-Zähler
Product name: Programmable Counter
Designation: Compteur universel
Descripción: Contador universal
Typ / Type / Type / Tipo: HM8123
mit / with / avec / con: HO820
Optionen / Options /
Options / Opciónes: HO880
mit den folgenden Bestimmungen / with applicable regulations /
avec les directives suivantes / con las siguientes directivas:
EMV Richtlinie 89/336/EWG ergänzt durch 91/263/EWG, 92/31/EWG
EMC Directive 89/336/EEC amended by 91/263/EWG, 92/31/EEC
Directive EMC 89/336/CEE amendée par 91/263/EWG, 92/31/CEE
Directiva EMC 89/336/CEE enmendada por 91/263/CEE, 92/31/CEE
Niederspannungsrichtlinie 73/23/EWG ergänzt durch 93/68/EWG
Low-Voltage Equipment Directive 73/23/EEC amended by 93/68/EEC
Directive des equipements basse tension 73/23/CEE amendée par 93/68/CEE
Directiva de equipos de baja tensión 73/23/CEE enmendada por 93/68/EWG
Angewendete harmonisierte Normen / Harmonized standards applied /
Normes harmonisées utilisées / Normas armonizadas utilizadas:
Sicherheit / Safety / Sécurité / Seguridad:
EN 61010-1:2001 / IEC (CEI) 1010-1:2001
Überspannungskategorie / Overvoltage category / Catégorie de surtension /
Categoría de sobretensión: II
Verschmutzungsgrad / Degree of pollution / Degré de pollution / Nivel de
polución: 2
Elektromagnetische Verträglichkeit / Electromagnetic compatibility /
Compatibilité électromagnétique / Compatibilidad electromagnética:
EN 61326-1/A1: Störaussendung / Radiation / Emission: Tabelle / table /
tableau 4; Klasse / Class / Classe / classe B.
Störfestigkeit / Immunity / Imunitee / inmunidad:
Tabelle / table / tableau / tabla A1.
EN 61000-3-2/A14: Oberschwingungsströme / Harmonic current emissions /
Émissions de courant harmonique / emisión de corrientes armónicas: Klasse
/ Class / Classe / clase D.
EN 61000-3-3: Spannungsschwankungen u. Flicker / Voltage fluctuations
and flicker / Fluctuations de tension et du flicker / fluctuaciones de tensión
y flicker.
Datum / Date / Date / Fecha
19. 08. 2005
Unterschrift / Signature / Signatur / Signatura
G. Hübenett
Product Manager
16
Subject to change without notice

General remarks regarding the CE marking

HAMEG measuring instruments comply with the EMI norms.
Our tests for conformity are based upon the relevant norms.
Whenever different maximum limits are optional HAMEG will
select the most stringent ones. As regards emissions class 1B
limits for small business will be applied. As regards suscep-
tibility the limits for industrial environments will be applied.
All connecting cables will influence emissions as well as sus-
ceptability considerably. The cables used will differ substantially
depending on the application. During practical operation the
following guidelines should be absolutely observed in order to
minimize EMI:
1. Data connections
Measuring instruments may only be connected to external
associated equipment (printers, computers etc.) by using
well shielded cables. Unless shorter lengths are prescribed
a maximum length of 3 m must not be exceeded for all data
interconnections (input, output, signals, control). In case an
instrument interface would allow connecting several cables
only one may be connected.
In general, data connections should be made using double-
shielded cables. For IEEE-bus purposes the double screened
cable HZ72 from HAMEG is suitable.
2. Signal connections
In general, all connections between a measuring instrument
and the device under test should be made as short as possible.
Unless a shorter length is prescribed a maximum length of 3 m
must not be exceeded, also, such connections must not leave
the premises.
All signal connections must be shielded (e.g. coax such as
RG58/U). With signal generators double-shielded cables are
mandatory. It is especially important to establish good ground
connections.
3. External influences
In the vicinity of strong magnetic or/and electric fields even
a careful measuring set-up may not be sufficient to guard
against the intrusion of undesired signals. This will not cause
destruction or malfunction of HAMEG instruments, however,
small deviations from the guaranteed specifications may occur
under such conditions.
HAMEG Instruments GmbH General remarks regarding the CE marking