Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
÷
÷
REMOTE
CONTROL
4.
SLEEP Button = To set the TV to turn off after a preset
10
1. POWEB Button = Press to turn on the TV. Press again
to turn off the TV.
2. Direct ChanneB Seiection
Buttons
(0-9} = Allows direct
access to any channel.
3. CH BTN Button = Repeatedly press CH RTN to toggle
back and forth between the last two channels you tuned.
amount of time, press the SLEEP button on the remote
control. The clock will count down 10 minutes each time
the button is pressed in the order of 120, 110, 100, ..-.. 20,
10, 0. After the sleep time is programmed,
the display will
disappear then reappear momentarily
every ten minutes to
remind you the sleep timer function is operating. To
confirm the sleep time setting, press the SLEEP button
once and the remaining time will be momentarily displayed.
To cancel sleep time, press the SLEEP button repeatedly
until the display turns to 0.
5.
VOL (VOLUME}
+/= Buttons = Press the + button to
increase, or the - button to decrease the volume level.
6.
MENU Button = Press to display the on-screen menu
function.
7.
SET + / - Buttons
- Press to select the desired setting
during on-screen operations.
8.
BESET Button
- Press to reset the on-screen picture
adjustments to their factory preset positions.
9.
TViVIDEO
Button = Switches between the TV and external
device inputs.
10. RECALL
Button = When you press this button, the
channel number will appear in the upper right corner of the
screen. Press the button again to remove it from the
screen.
11. MUTE Button
- To turn off the sound, press this button
once. The TV will be silenced and the word "MUTE' will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL + or
- buttons.
12. OH (CHANNEL)
+ / = Buttons = Press the + button to
change to a higher numbered channel set into memory.
Press the - button to change to a lower numbered channel
set into memory.
13. ENTER Button = Press to enter or select information for
On-screen operations.
14. 1/2 Button
- Switches between channel 1 and channel 2
in the closed caption mode.
15. CAP!TEXT Button - Press to switch between normal TV
and the two closed caption modes (captions or text), when
available.
÷
Before
using the remote
control,
batteries
must first be installed.
HOW
TO iNSTALL
BATTERIES
Use two 'AAA" size penlight
batteries
(supplied)
for the
remote control.
The batteries
may last approximately
one
year depending
on how much the remote control is used.
For best performance,
it is recommended
that batteries
should be replaced
on a yearly basis, or when the remote
operation
becomes
erratic.
1= Open the battery
compartment
cover.
2. Install two "AAA"
(penlight
size) batteries.
3. Replace
the battery
compartment
cover.
6
BATTERY
PRECAUTmONS
These precautions
should
be followed
when using batteries
in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct
polarity
when installing the
batteries
as indicated
in the battery compartment.
Reversed
batteries
may cause damage
to the device.
3. Do not mix different
types of batteries
together
(e.g.
Alkaline
and Carbon-zinc)
or old batteries with fresh
ones.
4. If the remote control will not be used for a !ong period of
time, remove the batteries
to prevent
damage
or injury
from possible battery
leakage.
5. Do not try to recharge batteries not intended to be recharged;
they can overheat
and rupture.
(Follow battery
manufacturer's
directions.)
3M12701A-E
P02-07
÷
5/2/04,
10:02
Publicidad
Tabla de contenido
