Sears Kenmore 73141 Manual Del Usuario página 10

Ice Service
(continued)
Icemaker Water Line
Installation Requirements
You wilt need a shutoff valve, two
1/4" OD compression nuts, two
compression sleeves and enough
1/4" O D copper tubing to connect
refrigerator to water source_ (Your
Sears Store or Catalog Sales Office
has a kit available with a saddle-
type shutoff valve and copper
tubing Before purchasing, make
sure a saddle-type valve complies
with your local plumbing codes)
CAUTION: Do not install icemoker
tubing in areas where temperatures
fall below freezing
1. Find a 3/8" ( 10 ram) to 1"
(25 ram) vertical COLD water pipe
near the refrigerator When it is
necessary to connect into a
horizontal water pipe, make the
connection to the top or side, rather
than at the bottom to avoid drawing
off any sediment from the water pipe
2. Measure from INLET on rear of
refrigerator to water pipe Add 7'
(2 m) to allow far moving refrigerator
for cleaning This is the length of
'_/4" O.D, copper tubing you will
need for the job (length from water
valve to water pipe PLUS 7" [2 m])_
Be sure both ends of copper tubing
are cut square
3. Turn OFF main water supply,
Turn on nearest faucet long enough
to clear _ine of water
CAUTION: When using any
electrical device (such as a power
drill) to facilitate installation, be
sure the device is insulated or wired
in a manner to prevent the hazard
of electrical shock
4o Using a grounded drill, drill a
3/16" hole in the vertical cold
water pipe you have selected
PIPE .J r-'-" - WASHER
CLAMP x_. ,_=
SHUTOFF __
VALVE - -"-_L--'r"_,
i i EN°
I VERTICAL
I COLD WATER
l --,_,,, PIPE
5. Fasten shutoff valve to cold water
pipe with pipe damp,_ Be sure inlet
end is solidly in 3/16" drilled hole
in water pipe and washer is under
pipe clamp, Tighten packing nut.
Tighten pipe clamp screws carefully
and evenly so washer makes a
watertight connection, Do not
overtighten or you may crush
copper tubing, especially if soft
copper tubing is used Nowyou are
ready to connect the copper tubing,
SHUTOFF i<_
PACKING /
NLIT
OUTLET
VALVE
I COMPRESSION
N UT
SLEEVE
6. Slip compression sleeve and
compression nut on copper tubing
as shown above Insert end of
tubing into outlet end squarely as far
as it wilt go, Screw compression nut
to outlet end with adjustable
wrench Do not overtighten Turn
ON main water supply and flush out
tubing until water is clear, Turn OFF
shutoff valve on water pipe_ You are
now ready to connect other end of
1/4" copper tubing to water valve
on back of refrigerator
way s to
connect
to water
supply u ,
Througk_ floor Under sinkto Through woll in crawl
_obasement co_dWa_er toutility room spaceunder
co_d wa_er pipe pipe could water p_pe house
TUBING
CLAMP
1/4°'TUBE TO
//j SHUTOFF VALVE
I/4" COMPRESSION NUT
REFRIGERATORCONNECTION
7o The water vaJve (supplied in the
icemaker kit, if not already on your
model) has a compression fitting
protruding through the compressor
compartment cover at the rear
of the refrigerator, Assemble
compression nut on compression
fitting as shown above Insert end
of tubing into connector and tighten
compression nut, Be sure end of
tubing issquare in connector and
is inserted as far as it will go Do not
overtighten. Be sure there is enough
extra tubing (coiled into three turns
of about 10" (25 cm) diameter) to
allow refrigerator to move out from
wall after installation Secure tubing
in metal clamp attop right corner of
compressor compartment cover_
8. Turn shutoff valve ON. TIGHTEN
ANY CONNECTIONS OR NUTS
THAT LEAK
9, Copper tubingmay now be
fastened to baseboard
100 Your ice cubes can only be as
fresbtasting as the water that
produces them. That s why it is a
good idea to purify the water with
a water filter. The water filter isan
optional part at extra cost and is
available from the Sears Service
Center Order Filter Na 978488
and install at the inlet water tube
connection,
11. Water Pressure Limitations:
Not below {15 PSI.) or above
( ] 25 P,SJ )_ tf a problem occurs,
call your Utility Company.
IMPORTANT: It may take up to 24
hours for your icemaker to begin
producing ice
The first few batches of ice cubes
should be thrown away, so that
remaining impurities in the water
line will be flushed out
10