Starting The Dishwasher - Ariston LI 480 A Instrucciones Para La Instalación Y El Uso

Starting the dishwasher

Ready, steady, go!
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
First of all.
After performing all the op-
erations described in the
previous paragraphs, turn
the water tap on completely,
open the appliance door and
press ON-OFF button "A":
indicator light "B" comes
on. Your appliance is now
on and awaiting instruc-
tions.
Selecting the wash
cycle.
Select the wash cycle by
pressing button "P". Each
time this button is pressed,
one of the indicator lights
"M" will come on in se-
quence, select the wash cy-
cle you deem most suitable
for the type of dishes to
wash (take a look at page
17, where you will find the
wash cycle table). Close the
appliance door and after a
few seconds, you will hear
a short beep: the wash cy-
cle has begun.
Modifying a wash cycle in
progress.
But if you have chosen the
wrong cycle, not to worry!
You can modify the wash
cycle in progress, if it has
only just started. Open the
appliance door carefully to
avoid any hot water
splashes, then keep button
"P" pressed for approxi-
mately 5 seconds, until you
hear 3 short beeps. Indica-
tor light "M" will come off
and at this point, all the set-
tings will have been can-
celled. You are now free to
re-set the correct wash cy-
cle.
You can modify
the wash cycle in
progress, if it
has only just
s t a r t e d .
You've left out a dish?
Well, it happens to every-
one. Interrupt the wash cy-
cle by opening the appliance
door with the utmost care,
as usual, then insert the
dish you had forgotten.
When you shut the appli-
ance door, the cycle will
start up from where you in-
terrupted it.
Finished?
The end of the wash cycle
is indicated by a double
beep and the flashing of the
wash cycle indicator light
"M".
Warning!
Open the dishwasher
door, turn off by
pressing button "A", un-
plug the appliance from
the electricity socket to
cut off the power supply;
the power supply cable
should consequently be
easily accessible.
Turn off the water tap.
Wait a few minutes before
unloading the dishes: they
are very hot! If you wait a
little while, they dry better
thanks to the steam.
Empty the lower rack first.
There's been a power
failure? Have you
opened the
dishwasher door?
The wash cycle stops and
then restarts when the
electricity comes back on or
when you close the door.
Everything is under control!
Make sure the
wash cycle has
ended before
removing the
d i s h e s !
You decide when it
starts.
When you have loaded the
dishes, you can choose
when to start your
dishwasher before setting
the wash cycle desired.
Press button "C" to delay the
start of the wash cycle by
2, 4 or 6 hours. Each time
you press it, you will hear a
short beep and indicator
light "D" corresponding to
the selected delay will come
on.
Now you can select the
desired wash cycle.
Close the appliance door
and, after you hear the beep,
the countdown to the
delayed start will begin.
Once this time is up,
indicator light "D" will stop
flashing and the wash cycle
will begin.
If opening the door
soon after the end
of the
p r o g r a m m e , o r
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
s t e a m .
ARISTON DISHWASHER - Instructions for installation and use
D
1509)50-4
Have you changed
your mind?
If you change your mind and
you wish to set a different
delay, just open the
appliance door, press button
"C" and repeat the selection.
If on the other hand you
want to cancel the delay set
and you wish to start the
wash cycle immediately,
press the button in sequence
until indicator light "D"
comes off.
Once you close the appliance
door, the wash cycle set
previously will begin.
If you have delayed the
start of your wash cycle,
it is best if you do not
modify anything while
you wait during the
countdown.
If you really have to,
then press button "P"
and keep it pressed down
for approximately 5
second You will hear 3
short beeps and all the
settings will be cancelled.
You can now repeat the
programming operations.
15