Turning The Tv On/Off; First Time Installation; Demo Mode; Reading Media Through The Usb Input - CONTINENTAL EDISON CELED323DML3 Manual De Instrucciones

Getting started
First time installation - USB connections

Turning the TV on/off

To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz.
To switch on the TV from standby mode either:
To switch on the TV from standby mode either:
• Press the " " button, P+ / P- or a numeric button
on the remote control.
• Press the " " or P/CH+/- button on the TV.
The TV will then switch on.
Note: If you switch on your TV via P+ / P- buttons on the
remote control or P/CH+/- on the TV set, the programme that
you were watching last will be reselected.
To Switch the TV Off
Press the " " button on the remote control or press
the side function switch until the TV switches into
standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode, the standby LED
can blink to indicate that features such as Standby Search, Over
Air Download or Timer is active. The LED can also blink when you
switch on the TV from standby mode.

First time installation

When you turn on the television for the first time,
the language selection menu appears. Select the
language you want and press OK.
The First time installation (FTI) screen appears
during first installation. Set your preferences using
the browsing buttons. When you are through, press
OK to continue.
IMPORTANT : If you chose France or Italy as an
alternative, the PIN code menu will appear and you
will have to enter 4-digit code. You will not be able
to use 0000 as code (you are advised to write down
this code on your instruction manual so that you can
remember it when you need to use it). Enter a PIN
code and confirm by entering it again. Press the OK
button to continue.
WARNING : When prompted to enter a PIN code to
access a menu item, you have to use the code you
set during first installation. If you forget the said code,
use the main code 4725.

Demo Mode

If you want to use your television inside a home, you
are advised to select the home mode.
If you choose the shop mode, you will have to confirm
your choice.
Choosing TV receiver mode
You will have to choose your reception mode, antenna
or cable. If you choose the ANTENNA option from
the Type of search screen, the digital television will
search for digital terrestrial broadcasts.
NOTE: You can press the MENU button to cancel.
Once all the available channels have been saved, the
list of the channels will appear on the screen. If you
find the said channels interesting, depending on the
LCN(*), select Yes, then press OK.
Press the MENU button to exit the list of channels and
watch the television.
(*) LCN Channel number system which displays
channels in the order established by government
agencies .
Installing the cable
If you choose the CABLE option and press the
OK button on the remote control. You can set
the frequencies manually or press OK to start an
automatic search.
Note: The duration of the search will depend on the search
zone selected.

Reading media through the USB input

You can connect external hard drives (hard drives with or
without external power cables, depending on their voltage)
or a USB port to your TV through your TV's USB ports.
IMPORTANT! Backup your files before making any
connection to the TV. Note that the manufacturer
shall not be held accountable if files are damaged or
data lost. Some types of USB devices (MP3 players
for example) or USB ''hard drives / memory cards''
''may be incompatible with this television. This
television supports FAT32 and NTFS disk formatting.
However, you will not be able to record with NTFS
formatted disks.
If your hard drive's capacity is above 1TO, you
may experience some issues with formatting. Avoid
disconnecting your reader quickly after inserting it in
the television's USB port. This can physically damage
the USB reader and the USB device itself. Never
remove the USB while a file is being read.
English - 36 -