Best KITE 800 Manual De Instrucciones página 2

ENGLISH
DESCRIPTION
The appliance can be used in both the filtering and ducting version. In the Filtering version (Fig. 1), the air and vapours
conveyed by the appliance are depurated by charcoal filter(s) and recirculated around the room. ATTENTION: Using the
hood as a filtering one it is necessary to use the charcoal filter(s) that purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapours and odours are conveyed straight outside by a disposal duct which passes
through the wall/ceiling. Use of charcoal filter is therefore unnecessary.
INSTALLATION
Before assembling, in order to manoeuvre the appliance more easily, take off the grease grille (Fig. 3): pull the
front of the grille upwards; desinsert the back from its seat.
IMPORTANT: So as not to damage your product, during installation USE ONLY THE SCREWS PROVIDED. Make
sure these are used as shown in the following instructions.
To compensate possible depth voids between the appliance and the wall, a plastic spacing bar to be fixed at
the back of the appliance by means of the three screws A is included (Fig. 4). The 3 screws A to be used are contained
in the accessory bag attached to the plastic spacing bar. Cut the spacing bar according to the distance to be adjusted.
Assembly under a pensile cupboard: The following operations are essential for as-sembly:
– Install the wiring system
– Prepare the air venting hole if your appliance is to be installed in the Ducting version.
Fixation as indicated in Fig. 5:
Using the relative template make the 4 necessary fixing holes in the bottom of the cupboard and cut the air
venting hole. Move the hood close to the bottom of the wall unit and then connect the two units by means of the 4 self-
tapping screws supplied together with the appliance.
Fixation with brackets as in Fig. 6 (optional):
Take the two brackets (S) out of the accessory bag together with the 12 screws provided. Fit the brackets to the wall
unit being careful to position these correctly; for this operation use the 8 shorter screws. At this point, secure the
appliance to the brackets using the 4 longer screws.
Ducting version: connect the flange of the hood with the air venting hole made previously in the wall/ceiling by means
of an adequate tube. Make the electrical connection of the hood by means of the power supply cable. Assemble the
grease grille with the hood, inserting it obliquely (making the front side go upwards).
Filtering version: connect a proper pipe to the flange of the hood so that the air is sent outside the pensile and sent
back into the room. Make the electrical connection of the hood by means of the power supply cable.
Remember that charcoal filter/s must be used in the case of the filtering version; check to see whether such filters are
already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:
- if the hood features round charcoal filters (Fig. 7), fit the charcoal filters by turning them.
- if the hood features a panel type charcoal filter/s (Fig. 8), position the panel (A) inside the grease grille and secure with
the 2 metal wires (F) provided, as shown in the illustration; the 2 metal wires must be threaded into the relevant slots.
Assemble the grease grille with the hood, inserting it obliquely (making the front side go upwards).
OPERATION
Controls (Fig. 9):
A = ON/OFF 1st speed switch
B = II speed switch
C= III speed switch
The motor is automatically ON or OFF by opening/closing the truck (unless switch A is on 0). Opening the truck
the motor works according to last speed registered.
D= Light switch:position A (automatic), the light are automatically regulated ON or OFF by the opening/closing of the
truck. Position M (manual), the light is on. Position 0, the light is off.
In case the hood is a filtering version one, it is necessary to change the charcoal filter(s) according to utilization about
every six month. To remove the filter:
– open the truck pulling it first downwards, then towards the front.
– take off the grease grille: pull the front of the grille upwards; desinsert the back from its seat.
– To remove the charcoal filters, proceed as follows, depending on the model purchased:
if the hood features round charcoal filters (Fig. 7), remove the charcoal filters by turning them.
if the hood features a panel type charcoal filter (Fig. 8), remove the charcoal filter by first of all removing the two filter
retainers F.
Light bulb:
If the fluorescent light or incandescent lamps need changing, slacken the light cover by disconnecting the screw
and remove the bulb itself (Fig. 10). Replace with a bulb of the same type.
To change the rectangular halogen bulbs open the cover and remove the bulb without touching it with bare hands
(Fig. 11). Replace with a bulb of the same type.