Technical Data - EINHELL ST 315 Manual De Instrucciones Original

Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

Weight of slide ................................ approx. 5 kg
The slide is suitable for use as an accessory for
the following bench-type circular saws:
•
TC-TS 315 U (Art. No.: 43.405.56)
•
TE-TS 315 U (Art. No.: 43.405.57)
•
TE-TS 315 UD (Art. No.: 43.405.58)
Anl_ST_315_SPK9.indb 14 Anl_ST_315_SPK9.indb 14
GB
5. Assembly
Caution! Always screw together the connections
which have self-locking nuts by turning the hex
screw while holding the self–locking nut fi rmly to
fasten tightly.
Fitting the accessory slide (Figs. 1, 3)
•
On the bench-type circular saw: Remove the
guide rail for the universal stop.
•
Fit the slide plate (100) and stop rail (101) to-
gether. To do so, use the large hexagon screw
(107) and medium washer (116) at the pivot
point. In addition, fasten the clamping lever
(106) using two large washers (108) and the
self-locking nut (109). Important! The clam-
ping lever (106) must be mounted in such
a way that the stop can be moved when the
clamping lever is released and is locked when
the clamping lever is secured. Adjust the
clamping force with the self-locking nut (109).
•
Fit the two angles (103, 104) to the guide
rail (102) using the washers (113), spring
washers (114) and hexagon screws (112).
•
Then fasten the angles (103, 104) together
with the guide rail (102) to the left legs (29) on
the bench-type circular saw. To do this, use
one hexagon screw (112), two washers (113),
one spring washer (114) and one nut (115) at
each point.
•
Place the slide plate (100) together with the
stop rail (101) onto the guide rail (102) from
the front.
•
If there is any slackness between the guide
rail and the running bearings of the slide pla-
te, then the two lower bearings must be ad-
justed using the screw (A) and the eccentric
screw (B), so that the slide can glide freely.
•
Fit the socket head screws (110) to the front
and rear of the guide rail (102) together with
the locking grip (111); they serve as a limit
stop.
•
The stop rail (101) must move parallel to the
saw table at a distance of approx. 1 mm. Sla-
cken the screws for the angles (103, 104) to
do this. Then adjust adjust the rail in such a
way that there is a 1 mm gap between the rail
and the saw table in every position.
•
Please note that for technical reasons relating
to delivery, some loose screws/washers may
be left over even if the slide is assembled and
fitted correctly (special accessory), because,
e.g. they may already be provided on the
bench-type circular saw.
- 14 -
11.03.2020 15:03:39 11.03.2020 15:03:39