Sammic CK-5 Instrucciones De Uso página 7

there is a safety device that is not activated.
Fast speed light (13)
If this is lit, it indicates that the machine is working
in fast mode. If you press the "Fast button" (11)
and this light blinks, it means there is a safety
device that is not activated.
Model (10)
Indicates the model of the
machine.
CKE mode (ffigure ))
Display (1)
Shows speed, operating time and
warnings.
Speed light (2)
When it is on, the display (1) shows the
speed.
Time light (3)
When it is on, the display (1) shows the
time.
Function (4)
This button switches between the
speed (2) and time (3) functions.
The selected function appears on the display and
the pilot light comes on.
Up (5)
Each time the key is pressed the
setting on the display (1) increases.
Down (6)
Each time the key is pressed the
setting on the display (1) decreases.
On (7)
Starts the motor if the safety
devices are activated. If any of the safety devices
is missing and you press "On" (7), the display (1)
shows "SE" (safety) to warn that a safety device
is missing.
Shutdown (8)
Pressed once, the motor stops
and the display (1) starts to flash to show that it is
on standby. The time and speed settings are still
saved. After 3 minutes, or if the "off" button is
pressed again, the machine loses those settings
and is reset.
Pulse (9)
While it remains pressed down, the motor
switches on if the safety devices are activated.
When released, the motor stops. If any of the
safety devices is missing and you press "Pulse"
(9), the display shows "SE" (safety) indicating that
a safety device is missing.
Model (10)
Indicates the model of the machine.
PLS. NOTE: Some vegetable preparation
machines have an emergency stop button.
This must be unlocked before starting the
machine.
OPERATION
CK models only (Figure 1 and 3)
When the CK is connected the "Machine
connected to mains" light is lit (14). If the bayonet
mechanism (Y) is open (position AA) the slow and
fast speed lights blink (12 and 13). If the lid (U) is
not placed the speed light (12 or 13) blinks. With
the bayonet mechanism (Y) closed (position Z)
and the lid (U) in place, if the "Slow button" (7),
"Fast button" (11) or "Pulse" (9) buttons are
pressed, the machine will start.
The machine will stop automatically if no action
has begun within 15 minutes.
CKE models only (Figure 2 and 3)
When the CKE is connected the display (1) has
two lines in the centre (standby). When the
cutter/emulsifier attachment is fitted the display
(1) shows "CU" for 2 seconds. By default the
speed selected by the machine is 5.
Speed Control: This is displayed with the "Speed"
light (2) lit and speeds from 1 to 10 can be
selected.
Time Control: It is displayed when the "Time" pilot
light (3) switches on. There are two functions,
continuous mode and time-out:
Continuous mode: A rotating line on the display
means that this has been selected. The machine
will stop automatically if no action has begun
within 30 minutes. Time-out: A time-out between
0 and 10 minutes can be programmed. The time
is selected in ½ minute intervals. The "Display" (1)
shows the countdown in the same way. The last
minute counts down in seconds. When the
programmed time finishes, the machine stops
and beeps.
Energy saving: If the machine is stopped and no
button is pressed on the display (1) for 5 minutes,
it switches off and only a dot is displayed. Press
any button to switch it on again.
START-UP
WARNING:
Before using the machine for the first time,
clean the area in contact with food with
(lukewarm) soapy water, rinse and leave to
dry.
The blade set (T) of the cutter/emulsifier has
very sharp blades, so they must be handled
with care.
Figure 3. With the bayonet mechanism (Y) open
(AA), fit the "Cutter" attachment on the motor so
that the three attachment lugs are inserted in the
quick-connect mechanism holes. The handle
must be placed just above the keypad for the
machine to operate. Close (Z) the bayonet
mechanism (Y) to lock the attachment on the
motor block.
Fit the blade set (T) and close the lid (U) by
rotating it anti-clockwise until it locks into
place. You can now operate the machine.
The lid (U) has hole to feed the product through
while the machine is functioning.
In addition the cutter/emulsifier models include a
scraper which, when rotated, the stirs the
contents (S) so that they are processed more
evenly.
ATTACHMENTS AVAILABLE FOR THE CK AND
CKE CUTTER/EMULSIFIERS.
- Smooth blade
- Perforated blade
- Finely serrated blade
- Mixer
Consult the Sammic Catalogue.
CLEANING
WARNING:
Disconnect the machine from the mains
EN 7