Normal Operation; Qs Link Input(S) Setup; Using Leds To Troubleshoot - Lutron Electronics Energi Savr Node Guia De Instalacion

Energi Savr Node

Normal Operation

In normal operation, the following buttons allow the user to access
certain basic functions:
•  (Raise)
– QSN-4T16-S and QSN-4T16-S-347: Raises zone light level in 1%
increments from 0–100%.
– QSN-4S16-S and QSN-4S16-S-347: Turns selected zone on.
•  (Lower)
– QSN-4T16-S and QSN-4T16-S-347: Decreases zone light level in 1%
decrements from 100–0%.
– QSN-4S16-S and QSN-4S16-S-347: Turns selected zone off.
Note: On QSN-4T16-S and QSN-4T16-S-347: For any zone,
simultaneously pressing and holding the  and  buttons will toggle the
zone between high end and low end.

QS Link Input(s) Setup

seeTouch QS wallstation or GRAFIK Eye
®
Scenes and Scenes + Off
Assigns a seeTouch QS Wallstation or GRAFIK Eye
®
unit zone on the QS link.
1. To assign a seeTouch QS Wallstation or GRAFIK Eye
®
unit, simultaneously press and hold the top and bottom buttons on the
wallstation or the top and bottom scene buttons on the GRAFIK Eye
unit for 3 seconds. The QS link enters Programming Mode. The sensor
LEDs on the ESN unit(s) will flash sequentially through each input and
group.
2. To assign or un-assign desired zone(s) to a wallstation, simultaneously
press and hold the the  and  buttons for the desired zone. A blinking
"Zone" LED indicates an assigned zone.
3. To exit Programming Mode, simultaneously press and hold the top and
bottom buttons on the wallstation or the top and bottom Scene buttons
on the GRAFIK Eye QS unit for 3 seconds.
®
Note: For more advanced programming information, refer to the online
Programming Guide at:
www.lutron.com/Softswitchenergisavrnode
14 | Lutron
®
for 0 –10 V / Energi Savr Node
TM
QS unit:
®
QS unit to any ESN
®
QS unit to an ESN
®
with Softswitch
TM

Using LEDs to Troubleshoot

WARNING! Danger of Shock. May result in serious injury or
death. DO NOT WIRE WHEN LIVE! Switch off power to all power
feeds via circuit breaker before wiring or servicing the ESN unit.
Buttons and LEDs in the unit are used for programming and
troubleshooting. If line voltage shield is removed, the unit
must be accessed by a certified electrician, following local
codes.
LED
Occ
(Occupancy Sensor)
Photo
(Daylight Sensor)
IR
(Keypad or Infrared
Receiver)
Switch
QS
®
(IEC PELV / NEC
®
Class 2)
CCI
(Contact Closure
Input)
Emerg
(Emergency Contact
Closure Input)
QS Link
Wired
Zone
| Installation Guide
®
LED Behavior Description
Continuous On Sensor detects Vacancy
1 flash per second Sensor detects Occupancy
Off Sensor never detected
Continuous On Sensor is detected
Flashing Sensor information transmitting
on the QS link
Off Sensor never detected/sensor not
seeing light
Continuous On Keypad or IR Receiver detected
Flashing IR button press detected
Off Keypad or IR Receiver never
detected
Continuous On Switch detected/open
Flashing Switch button press detected
Off Switch never detected
Continuous On Contact detected/open
Flashing Contact closed
Off Contact never detected
Continuous On Normal operation/Contact Closed/
Jumpered
Rapid flash Emergency Mode/Contact Open/
Jumper missing
On/Flashing Device transmitting/receiving on
the QS link
3 quick flashes Communication error
every 4 seconds
Off Device not transmitting/receiving
on the QS link
Continuous On Wired sensor
Continuous On Load is on
Off Load is off