User Manual; Ignition; Controlling The Temperature; Switching Off - Dru Verwarming ART 2-01 Manual De Instalación Y Guía Del Usuario

USER MANUAL

USER MANUAL

Ignition

Ignition button A has three positions, i.e.:
USER MANUAL
O position
Pilot burner position
Ignition
Full position
Ignition button A has three positions, i.e.:
Turn the ignition button to the left from position O,
O position
press down firmly as well and keep turning to the
Pilot burner position
pilot burner position . By turning the button, the
Full position
pilot burner is ignited by means of an electrical
spark. When the pilot burner burns, keep pressing
Turn the ignition button to the left from position O, press
down the button for approx. 10 sec. and then let
down firmly as well and keep turning to the pilot burner
go. The pilot burner is visible from the side, behind
position . By turning the button, the pilot burner is igni-
the glass window. If the pilot burner does not
ted by means of an electrical spark. When the pilot burner
burns, keep pressing down the button for approx. 10 sec.
ignite at once, the above-mentioned action can be
and then let go. The pilot burner is visible from the side,
repeated immediately by turning the pressed down
behind the glass window. If the pilot burner does not
button back towards O and then left again towards
ignite at once, the above-mentioned action can be repea-
the pilot burner position. After letting go of the
ted immediately by turning the pressed down button back
ignition button, the pilot burner should continue to
towards O and then left again towards the pilot burner
burn. Then turn the ignition button further
position. After letting go of the ignition button, the pilot
towards the full position . Depending on
burner should continue to burn. Then turn the ignition
thermostat button B, the main burner will be
button further towards the full position . Depending on
ignited.
thermostat button B, the main burner will be ignited.

Controlling the temperature

Controlling the temperature
The position of thermostat button B determines
The position of thermostat button B determines the
the temperature in the room. Position 6 provides
temperature in the room. Position 6 provides the highest
the highest temperature, position 1 the lowest.
temperature, position 1 the lowest. The thermostat
The thermostat controls the burner by modulating
controls the burner by modulating between "full position"
between "full position" and "low position" of the
and "low position" of the burner. The thermostat will
burner. The thermostat will automatically keep the
automatically keep the room at the required set
room at the required set temperature.
temperature.

Switching off

Switching off
Turn ignition button A back to the Pilot Burner
Turn ignition button A back to the Pilot Burner position
position ( symbol), only the pilot burner will
( symbol), only the pilot burner will continue to burn.
continue to burn. In order to switch off the
In order to switch off the appliance fully, you must press
appliance fully, you must press down button A and
down button A and turn it back to position O.
turn it back to position O.

Important

Important
An incorporated safety lock will be activated if the appli-
An incorporated safety lock will be activated if the
ance is set to the ,,OFF" (O) position. Therefore, wait
appliance is set to the ,,OFF" (O) position.
5 minutes before re-igniting the appliance. Do not try
Therefore, wait 5 minutes before re-igniting the
to press down the ignition button during this time, as it is
appliance. Do not try to press down the ignition
locked by means of the safety lock. Do not force the
button during this time, as it is locked by means of
button, because the mechanism could get damaged.
the safety lock. Do not force the button, because

Eco control pack

the mechanism could get damaged.
It is possible to order a separately available "Eco control
pack" with remote control. The "Eco control pack" is
Eco control pack
needed to get the best out of your appliance.
It is possible to order a separately available "Eco
control pack" with remote control. The "Eco
button points to O
button points to
button points to
button points to O
button points to
button points to
control pack" is needed to get the best out of your
appliance.
This set has a receiver that must be placed in the
tray specifically intended for this purpose.
This set has a receiver that must be placed in the tray
specifically intended for this purpose.
Art 2-01: The tray is located on the left side of the
gas control.
Art 2-01: The tray is located on the left side of the gas
control.
Art 3-01, 4-01, 5-01, 6-01, 8-02, 10-02: The tray is
located under the gas control.
Art 3-01, 4-01, 5-01, 6-01, 8-02, 10-02: The tray is located
under the gas control.
Prevent cables from making contact with hot
internal components. Prevent cables from making contact with hot internal
components.
13
B
A
38P-0744/0
ART