Star Pro-Max Instrucciones De Instalación página 3

ELECTRONIC TEMP CONTROL OPERATION
Operating Instructions
1. The program number and display will flash indicating the unit
is heating for electronic units. When the preset temperature is
reached, the heating light, display and program light indicator
will stop flashing followed by 3 beeps.
2. Place product on the bottom cooking surface of the unit and
close the lids.
3. Eletronic Timer Models Only:
Press the PROGRAM button and let the displayed time
count down to "0" at which time the unit will beep. To turn
off the beeper, press the PROGRAM button again.
4. Raise the lid until it engages into the first detent and remove
food. Using a spatula, scrape residue into the grease catcher
tray.
NOTE: Metal utensils may be used, however, using nonmetal
utensils will prolong the life of the cooking surface.
5. Turn the unit off when it is not in use.
Temperature:
1. To view the actual temperature, press and hold the TEMP
button. The display will read "Lo" if the temp. is below 273°F
(135°C) and "Hi" if the temperature is above 573°F (300°C).
SPLIT LID UNITS
To Program Time and Temperature:
1. Press and hold "TEMP" (actual temperature displays).
2. While holding "TEMP", press and hold any program button on
the left for one second. The LED above the program number
will light and the display will read "_ _ _ _." Enter the four-digit
security code sequence: 4, 3, 2, 1. The security code will not
show on the display. Once the correct sequence has been
entered, the preset time will be displayed and the LED for that
program will begin to flash.
3. Set the desired time with the "+ or -" buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the "+ or
-" buttons.
7. Press the "TEMP" button to save the temperature and to exit
the programming mode for this program. The LED will stop
flashing but will remain lit.
8. Press any other program button within 15 seconds to
continue programming without re-entering the security
code.
9. While programming a program (LED is flashing), if no input is
received for 15 seconds the unit will revert to normal operation
and the security code must be re-entered.
NOTE: Temperature settings are done with the Left side buttons
only. The time settings programmed on the left buttons will also be
programmed onto the Right side. See the next section to make
time changes to the Right side only. Each programming change
must be saved by pressing the TEMP button!
Right Side (Timer only):
1. To change the time on right, Press and hold the TEMP button,
then press and hold any program button on the right for one
second. The LED above the program button will light and the
right display will read "_ _ _ _." Enter the four-digit security
code sequence: 4, 3, 2, 1. The security code will not show
on display. Once the correct sequence has been entered, the
preset time will be displayed and the LED for that program
will begin to flash.
2. Set the time with the "+ or -" buttons.
3. Press the TEMP button to save the time.
4. The LED will stop flashing but will remain lit.
5. Press any other program button within 15 seconds to continue
programming without re-entering the security code.
6. While programming a program (LED is flashing), if no input is
received for 15 seconds the unit will revert to normal operation
and the security code must be re-entered.
SINGLE LID UNITS
To Program Time and Temperature:
1. Press and hold TEMP (actual temperature displays).
2. While holding TEMP, press and hold any program button on
the left for one second. The LED above the program number
will light and the display will read "_ _ _ _." Enter the four-
digit security code sequence: 4, 3, 2, 1. The security code
will not show on the display. Once the correct sequence has
been entered, the preset time will be displayed and the LED
for that program will begin to flash.
3. Set the desired time with the "3" increase or "4" decrease
buttons.
4. Press the TEMP button to save the time.
5. The bottom and top temperature settings can now be
programmed.
6. The bottom temperature setting for the selected switch will
now be displayed.
7. Change the bottom temperature setting using "3" increase or
"4" decrease. Press the "TEMP" buttom when the desired
setting is displayed.
8. The top temperature setting for the selected switch will now
be displayed.
9. Change the top temperature setting using "3" increase or
"4" decrease. Press the "TEMP" buttom when the desired
setting is displayed.
10. Press any other program button within 15 seconds to continue
programming without re-entering the security code.