Crown CT19022K Manual Original página 17

Power tool designation
The hot air gun is designed for heating a work surface
by means of blowing with a hot air blast�
It also offers the possibility of weakly heated (50°С)
blowing on a work surface� This allows for the effective
performance of different types of work�
Power tool components
1 Nozzle
2 Protective casing
3 Body
4 Ventilation slots
5 On / off switch
6 Regulator
7 Scraper *
8 Flat nozzle *
9 Deflector nozzle *
10 Reflector nozzle *
11 Point nozzle *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Removal / installation of protective casing (see fig. 1)
• Turn protective casing 2 and remove it as shown on
fig. 1 (this may be necessary for performing works in
confined spaces).
• While installing protective casing 2 match the raised
elements inside the casing with the slots in housing 3,
put the casing on and turn as shown on fig. 1.
Using special nozzles (see fig. 2)
Put a special nozzle on nozzle 1 and turn, it if neces-
sary, to adjust it to a position more suitable for work
(see fig. 2). Notice that a special nozzle must be put
on evenly so that it will not fall off during operation�
Initial operating of the power tool
Always use the correct supply voltage: the power
supply voltage must match the information quoted on
the power tool identification plate.
Switching the power tool on / off
Switching on:
Move on / off switch 5 in position "1", "2" or "3"�
Switching off:
Move on / off switch 5 in position "0"�
Design features of the power tool
Temperature adjustment (see fig. 3)
[CT19023K]
The air flow temperature can be smoothly changed
with regulator 6 (only if on / off switch 5 is placed in po-
sitions "2" or "3")� Rotate regulator 6 to set the desired
temperature (see fig. 3)�
Cool air blowing
If on / off switch 5 is placed in position "1", the heating
element is not activated, and only the fan is running�
This mode is intended for cooling the power tool after
operation, and it also can be used for cooling, blowing
and drying�
Possibility of steady-state use (see fig. 6)
The power tool design allows steady-state operation�
Switch the power tool on, set the desired temperature
and then put it in a vertical position with the nozzle up
(see fig. 6).
Recommendations on the power tool
operation
Range of application of the power tool
Using the power tool allows different types of work to
be performed� Some of them are listed below�
• Contracting heat shrink pipes, soldering connec-
tors and clamps of sealing and electrical components�
• Changing the shape of acryl, PVC, polystyrene
products, pipes, plates, profiles and wet timber.
• Repairing surfboards, skis and other sports equip-
ment, repairing bumpers and other plastic automobile
parts�
• Waxing skis, furniture, and antiseptic timber treat-
ment�
• Loosening rusted or tight metal screws, nuts, bolts,
shrink-fitting, heat shrink treatment.
• Welding thermoplastic polymers, PVC and linoleum
flooring materials, PVC coated fabrics, tarpaulin and foil.
• Soldering, tinplating and loosening of soldered
joints�
• Removing lacquer and paint coatings�
• Drying lacquer and paint coatings, adhesive and
spackling compounds�
• Acceleration of adhesion processes, activation of
adhesives�
• Thawing ladders, stairs, door locks, boot covers, car
doors, water pipes as well as defrosting fridges and
freezers�
• Mold and fungus control, disinfection of animal
housing�
• Lighting charcoal�
Using special nozzles
• Flat nozzle 8 is designed for treating large-area sur-
faces�
English
17