Ingersoll Rand 7804R Manual De Instrucciones

Ingersoll Rand 7804R Manual De Instrucciones

Taladro angulares reversible
Ocultar thumbs Ver también para 7804R:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

Model 7804R and 7804R- -EU Drills are designed for drilling, honing, reaming and hole sawing.
Ingersoll- -Rand is not responsible for customer modification of tools for applications on which
Ingersoll- -Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16" (8 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905- - 1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from rotating end of tool.
The use of other than genuine Ingersoll- - Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- - Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll- - Rand Office or Distributor.
 Ingersoll- - Rand Company 2001
Printed in U.S.A.
INSTRUCTIONS FOR
MODEL 7804R AND 7804R- -EU
REVERSIBLE ANGLE DRILL
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03539962
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool accessory may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll- - Rand.
This tool is not desgined for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Prevent exposure and breathing of harmful dust
and particles created by power tool use:
Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement
and other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.
Form P7115
Edition 6
GB
August, 2001

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 7804R

  • Página 1 MODEL 7804R AND 7804R- -EU REVERSIBLE ANGLE DRILL Model 7804R and 7804R- -EU Drills are designed for drilling, honing, reaming and hole sawing. Ingersoll- -Rand is not responsible for customer modification of tools for applications on which Ingersoll- -Rand was not consulted.
  • Página 2: Placing Tool In Service

    ♦Vibrations dB (A) Level in (mm) pressure power • 7804R, 7804R- - EU pistol 1200 3/8 (10) 91.4 104.4 Tested in accordance with ANSI S5.1- - 1971 at free speed ♦ Tested in accordance to ISO8662- - 1 at 80% rated free speed ISO3744 •...
  • Página 3: Declaration Of Conformity

    (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (address) declare under our sole responsibility that the product, Model 7804R- EU Reversible Angle Drill to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives. EN292 ISO8662 By using the following Principle Standards: (1994 →...
  • Página 4: Utilisation De L'outil

    MODÈLE 7804R ET 7804R- -EU NOTE La perçeuse Modèle 7804R et 7804R- -EU est destinée aux opérations de perçage, de rodage, d’alésage et de sciage de trou. Ingersoll- -Rand ne peut être tenu responsable de la modification des outils par le client pour les adapter à...
  • Página 5: Mise En Service De L'outil

    (mm) Pression Puissance • 7804R, pistolet 1200 3/8 (10) 91,4 104,4 7804R- - EU Testé conformément à ANSI S5.1- - 1971 en vitesse libre ♦ Testé conformément à ISO8662- - 1 a 80% vitesse libre nominale ISO3744 •...
  • Página 6: Certificat De Conformité

    (nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (adresse déclarons sous notre seule responsabilité que le produit: Perceuse D’Angle Réversible Modèle 7804R- EU objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/CE EN292 ISO8662 en observant les normes de principe suivantes: (1994 →...
  • Página 7 HOCHLEISTUNGS- -WINKELBOHRMASCHINE DER BAUREIHE 7804R UND 7804R- -EU HINWEIS Winkelbohrmaschinen der Baureihe 7804R und 7804R- -EU werden eingesetzt zum Bohren, Honen, Räumen und Lochsägen. Ingersoll- -Rand lehnt jede Haftung für Veränderungen an Werkzeugen ab, die ohne vorherige Rücksprache mit Ingersoll- -Rand vorgenommen werden.
  • Página 8: Technische Daten

    - dB (A) intensität U/min Zoll (mm) Druck Leistung • 7804R, 7804R- - EU Pistolengriff 1200 3/8 (10) 91.4 104.4 Gemäß ANSI S5.1- - 1971 bei freier Drehzahl getestet ♦ Gemäß ISO8662- - 1 bei 80% der freien Nenndrehzahl getestet ISO3744 •...
  • Página 9: Konformitätserklärung

    Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Hochleistungs- Winkelbohrmachine Der Baureihe 7804R- EU auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen EN292 ISO8662 entsprechen: (1994 →...
  • Página 10 REVERSIBILE MODELLI 7804R E 7804R- -EU AVVISO Il trapano modello 7804R e 7804R- -EU è stato progettato per la trapanatura, smerigliatura. alesatura e segatura a tazza. La Ingersoll- -Rand non è responsabile delle modifiche apportate agli attrezzi dai clienti per adattarli ad applicazioni per le quali la Ingersoll- -Rand non sia stata interpellata.
  • Página 11 (mm) Pressione •Potenza 7804R, Impugnatura 1200 3/8 (10) 91.4 104.4 7804R- - EU Collaudato secondo i criteri ANSI S5.1- - 1971 a velocità libera ♦ Collaudato secondo i criteri ISO8662- - 1 a velocità libera nominale dell’80% ISO3744 •...
  • Página 12: Dichiarazione Di Conformità

    Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Trapani ad angolo reversibile modelli 7804R- EU a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE EN292 ISO8662 secondo i seguenti standard: (1994 →...
  • Página 13: Uso De La Herramienta

    TALADRO ANGULARES REVERSIBLE MODELO 7804R Y 7804R- -EU NOTA Los Taladros Angulares Modelos 7804R y 7804R- -EU están diseñados para taladrado, rectificación, rebordeado y serrado de agujeros. Ingersoll- -Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll- -Rand.
  • Página 14: Etiquetas De Aviso

    (mm) Presión •Potencia 7804R, pistola 1200 3/8 (10) 91.4 104.4 7804R- - EU Probado en conformidad con ANSI S5.1- - 1971 a velocidad libre ♦ Probado en conformidad con ISO8662- - 1 80% de la velocidad libre nominal ISO3744 •...
  • Página 15: Declaracion De Conformidad

    Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros Angulares de Modelo 7804R- EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 ISO8662 conforme a los siguientes estándares:...
  • Página 16: Gebruik Van Het Gereedschap

    TYPEN 7804R EN 7804R- -EU OMKEERBARE HAAKSE BOORMACHINES LET WEL De Typen 7804R en 7804R- -EU Haakse Boormachines zijn bedoeld voor het boren, honen, ruimen en gatzagen. Ingersoll- -Rand is niet aansprakelijk voor door de klant aangebrachte veranderingen aan de gereedschappen voor toepassingen waarover met Ingersoll- -Rand geen voorafgaand overleg werd gepleegd.
  • Página 17: Specificaties

    Houder niveau dB (A) in (mm) Deuk •Vermogen 7804R, 7804R- - EU pistool 1200 3/8 (10) 91.4 104.4 Getest volgens ANSI S5.1- - 1971 bij vrije snelheid ♦ Probado en conformidad con ISO8662- - 1 80% de la velocidad libre nominal ISO3744 •...
  • Página 18 Ingersoll- Rand, Co. (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Typen 7804R- EU Omkeerbare Haakse Boormachines waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG EN292 ISO8662 overeenkomstig de volgende hoofdstandaards: (1994 →...
  • Página 19 MAINTENANCE INSTRUCTIONS SECTION D’ENTRETIEN WARTUNG SEZIONE DI MANUTENZIONE INSTRUCCIONES DE MANTENIMIENTO ONDERHOUD (TPA1392)
  • Página 20 Throttle Lever Pin ... 107- - 120 Arbor ..... . 7804R- - 4 Reverse Valve Spring .
  • Página 21 Service Centers Centres d’entretien Ingersoll- - Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll--Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 45220 Fax: (31) 71 218671 Ingersoll--Rand Company 510 Hester Drive Ingersoll--Rand Company SA White House, TN 37188 PO Box 3720 Airode 1451...

Este manual también es adecuado para:

7804r-eu

Tabla de contenido