Symbols Used In The Manual - Crown CT10010 Manual Original

página de 152

/ 152
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

parts. This will ensure that the safety of the power tool

is maintained�

• Follow instruction for lubricating and changing ac-

cessories�

Special safety warnings

• Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury�

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electric shock�

Safety guidelines during power tool

operation

• The workpiece shall be fastened� Fixed devices or

vice shall be used to fasten the workpiece, which will

be more secure than holding the workpiece with your

hands�

• Considering that asbestos may cause cancer,

asbestos-containing materials shall not be processed�

• The power tool could be put down only after the

parts of power tool is completely static� Accessory on

the power tool might be clamped during work, which

may make it difficult for you to control the power tool.

• Power tool with damaged electric wires shall not be

used� If electric wires of the power supply are damaged

during the work, you shall not touch the damaged electric

wires and shall pull out the plug immediately� Damaged

electric wires will raise the risk of electric shock�

• When using power tools outdoor, you must install

fault current (FI) protection switch on the power tool�

• Appropriate detector shall be used to find the

location of hidden power wires� Or you should obtain

relevant information from local power supply unit�

Drilling electric wires will cause fire and electric

shock� Damaged gas pipe will cause exploration� If

water pipes are punctured, damage will be caused to

property�

• In case a accessory installed on the power tool

is clamped, you shall shut down the power tool and

stay calm� At that time, the power tool will produce

extremely high reactive torque thus resulting in return

stroke� The accessory installed on the power tool are

likely to be clamped, for example: hypercharge of

power tool or skewing of accessory installed on the

power tool during work�

• If hidden electric wires or power lines of the power

tool itself might be cut off during work, you must hold

the insulated handle to operate the power tool� When

the power tool is in touch with a charged line, the metal

parts on the power tool will conduct electricity and may

cause the operator to get an electric shock�

• During work, you must tightly hold the power tool

and ensure you stand firmly. You should hold the

power tool with your hands�

• When operating and using the power tool, you can

only hold switch position of the main handle rather than

other parts�

• Avoid stopping an power tool motor when loaded�

• Never remove any chips or fragments with your

power tool's motor running�

• When working, follow the position of the power sup-

ply cable� Avoid winding it around your legs or arms�

• Use only sharp drill bits without defects - it will make

working with the power tool easier�

• The modification of the drill bits design and the use

of removable orifices and accessories not envisaged

for this power tool is strictly forbidden�

• Do not apply excessive pressure when operating the

power tool - it can jam the drill bit and overload the

engine�

• Do not allow drill bits to jam in the material pro-

cessed� If this occurs, do not try to release them by

means of the power tool engine� This can put the pow-

er tool out of order�

• Striking out drill bits jammed in the material pro-

cessed with a hammer or other objects is strictly for-

bidden - metal fragments can hurt both the operator

and the people nearby�

• Avoid overheating your power tool, when using it for

a long time�

• When working, follow the position of the power sup-

ply cable� Warning: power cable may be entangled by

stirring paddle� Avoid winding it around your legs or

arms�

• In case the power tool should fall into the stirred so-

lution, switch off the plug immediately and have the

power tool checked by a service center� Material that

has penetrated into the power tool can cause damage

and lead to an electric shock�

• Do not process explosive substances (for example,

highly inflammable solvents) and materials with igni-

tion temperature of lower than 21°С. Study the manu-

facturer's instructions for such kind of materials care-

fully and stick to them�

• Take protective measures if combustible or explo-

sive dust, harmful to one's health, may appear during

working�

• It is strictly prohibited to use the power tool for mix-

ing any food products�

• The container for mixing must be durable enough,

and it must be placed on stable surface�

• When mixing, prevent splashes from getting on the

tool body as it may cause electric shock�

• Always wait until the power tool has come to a com-

plete stop before unhand it�

• Avoid overheating your power tool, when using it for

a long time�

• Don't operate the power tool in stationary mode (e�g�

placing it into special frame)�