Crown CT10010 Manual Original página 22

Installation and regulation of power tool
elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening ele-
ments too tight to avoid damaging the
thread.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Additional handle (see fig. 1-2)
[CT10010]
• Release additional handle 2 as shown on picture 1�
• Extract cap 19 and screw additional handle 2 into
the threaded opening�
• Insert cap 19 into the freed threaded opening�
[CT10148, CT10148M]
Mount / dismount additional handle 2 as shown on
fig. 2.
Additional back handle (see fig. 3-4)
The additional back handle 4 facilitates performance
of works and improves the control over the tool�
[CT10010]
• Release wing screw 18 (see fig. 3).
• Place additional back handle 4 in desired position
(additional back handle make have set in four posi-
tion)�
• Tighten wing screw 18�
[CT10148, CT10148M]
Install additional back handle 4 in desired position as
shown on fig. 4.
Mounting / replacement of accessories (into gear
rim chuck) (see fig. 5)
With long-term use the drill bit may be-
come very warm; use gloves to remove
it.
• Release the cams grip with drill chuck key 9, then
rotate the quill of gear rim chuck 1 counter-clockwise
with your hand (see fig. 5) until the cams move apart
at the distance allowing an accessory to be mounted /
replaced�
• Mount / replace an accessory�
• Rotate the quill of gear rim chuck 1 clockwise with
your hand in order to lock the accessory mounted� Do
not allow the accessory to become distorted�
• Tighten the cams of gear rim chuck 1 with drill chuck
key 9 applying a similar torque to each of the three
openings on the side surface of the chuck�
Mounting / dismounting of the drill chuck (see
fig. 6-7)
• To mount the gear rim chuck 1, carry out the opera-
tions in consecutive stages as it is shown in figure 6.
• To dismount the gear rim chuck 1, carry out the
operations in consecutive stages as it is shown in fig-
ure 7�
Attention: keep in mind that in the pro-
cess of mounting / dismounting of the
drill chuck the screw 14 has a left-hand
thread.
Mounting / replacement of stirrer paddle (onto spin-
dle) (see fig. 8-9)
[CT10148M]
Before installing the assembled stirrer
paddle (rod 12 and stirrer paddle 13), it is
necessary to remove the gear rim chuck 1
(as described above).
• Screw the stirrer paddle 13 on the rod 12 and tighten
them with two wrenches 10 (22 mm) (see fig. 8).
• While holding the spindle 15 with wrench (19 mm),
screw the hex coupling nut 11 on the spindle 15 and
tighten it with wrench 10 (22 mm) (see fig. 9.1).
• While holding the hex coupling nut 11 with wrench 10
(22 mm) , screw the rod 12 (with the stirrer paddle 13 put
on it earlier) in, and tighten it with wrench 10 (22 mm) as
shown on fig. 9.2.
• Disassembly operations do in reverse sequence�
Initial operating of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power tool on / off
[CT10010]
Short-term switching on / off
Rotation to the right ("F")
Press and hold the on / off switch 16 on the bottom
("F", see fig. 10.1), to switch off - release it.
Rotation to the left ("R")
Press and hold the on / off switch 16 on the top ("R",
see fig. 10.2), to switch off - release it.
Long-term switching on / off
Rotation to the right ("F")
Switching on:
Press the on / off switch 16 on the bottom and lock it
in the position with locking button for on / off switch 17
("F", see fig. 10.1).
Switching off:
Push on / off switch 16 and release it�
English
22