Input Options; Care And Cleaning - Sammic HM-2000 Instrucciones De Uso

The following modes can be selected by inputting one of the numbers bellow at
the operation stage "4".

Input options

1. Accumulative cooking time.
2. The number of door operations (100 times).
3. Indication of remaining cooking time (when cooking is interrupted by door
opening) .
4. To cancel remaining cooking time (when cooking is interrupted by door opening).
5. Tone of the buzzer on cooking completion, (Pip, Pip, Pip).
6. Tone of the buzzer on cooking completion. (Peep)
7. The volume of the buzzer. (quiet)
8. The volume of the buzzer. (medium)
9. The volume of the buzzer. (loud)
0. The volume of the buzzer. (none)

CARE AND CLEANING

ALWAYS KEEP THE OVEN CLEAN.
1. Cleaning the glass viewing window, the inner door panel and oven front face.
For best performance and to maintain the high degree of safety the inner
door panel and oven front face should be free of food or grease build-up.
Wipe these parts with a mild detergent, rinse and wipe dry.
Never use abrasive powders or pads.
2. Cleaning the oven interior
After use be sure to clean up spilled liquids, spattered oil and food debris as
quickly as possible. If the oven is used when dirty, efficiency drops and the
dirt gets stuck on the oven surface and may cause bad odours. Clean the
interior with a cloth soaked in luke-warm water with a mild detergent dissol-
ved in it, then rinse the soap off with a damp cloth.
In particular, the bottom of the oven interior tends to get stained from spices
and food. Since this may cause odour and abnormal vibration, be sure to
keep this area clean.
CAUTION: Do not wipe plastic and painted sections of the oven with bleach,
thinners or other cleaning agents, as this may cause these parts to dissolve
or change shape.
3. The stirrer shield (inside oven top) can be gently wiped in place or removed
for washing at the sink. The shield is a mica, supported at front, side and
rear. Carefully remove the shield secured at the front tabs, pull forward to
remove. Wash only in warm (not hot) detergent water, rinse and wipe dry.
Avoid hitting or bending the metal stirrer blades, as this could change the
heating pattern in the oven.
To replace the shield, position it on the rails on sides and rear of the cooking
chamber and secure it between the front metal tabs.
4. Clean the removable air filter regularly. (at least once a week)
Do not operate oven without air filter in position.
WHAT TO DO IF REPAIRS ARE NEEDED
1. If any of the following appear, check for a problem.
"U-50" flashes in the display window.
When using Programme Selection Keys the key must be touched within 1
minute of closing the door.
After inserting the power plug into the wall outlet, open and close the door and
then touch the key.
- Open and close the door, and then touch the key before 1 minute passes.
· The purpose of this function is to prevent operation when there is no food in
the oven.
"U-10" appears in the display window.
The oven operates empty without food in it.
- Touch CLEAR key, place food in oven and start again.
2. This is normal operation:
Cooling fan operates for a while after heating has completed or heating has
been stopped by opening door or touch CLEAR key during operating.
- Cooling fan operating continues for five minutes to keep the electronic com-
ponents cool.
3. This is abnormal operation:
Get in contact with your nearest Service center or retailer.
This oven is provided with self-diagnostic function.
- When the window display indicates the error code "E" (example: E-21), it
shows to need repairing by a technical service engineer. Remove the power
supply plug from wall outlet and call a Service Center.
- When the magnetron indicator in control panel lights, it shows that remaining
magnetron life became short. Call a Service Center to replace the magnetron
before it becomes defective.
· On no account remove or interfere with any parts or screws.
"THIS COULD PROVE VERY DANGEROUS."
Make the following simple check-up before contacting a Service Centre:
· If the interior lamp does not light when one of the programme selection key is
touched.
1. Make sure that the mains lead is securely plugged in.
2. Check the fuse in the plug top and ensure the plug top is wired correctly.
Note: The appliance must be protected by a fuse.
3. Make sure that the door is completely closed.
4. Make sure that a programme has been stored.
· Before changing the interior lamp, please confirm the power supply plug is
disconnected from the socket.
· If the interior lamp lights and the appropriate power select or preset cooking
indicator is illuminated but the food is not heated;
1. Make sure that the food is not completely covered with a metal container.
· Abnormal noise during operation.
1. Make sure that sparking during microwave cooking is not caused by using
unsuitable utensils of metal or having metal bands or trimmings, or alumi-
num foil or skewers.
2. Make sure that the tray is set in the oven properly.
3. Check whether foods or containers are touching inside walls of the oven.
· If smoke is observed, keep the oven door closed and switch off by discon-
necting the oven from the power supply.
SPECIFICATIONS
Specifications HM-2000
Microwave power output
Microwave frecuency
Outer dimensions
Cavity dimensions
Weight
Accessoires
Operating instructions 1
Air filter 1
1800W - 180W
2450 MHz
610 x 493 x 410 mm
374 x 413 x 238 mm
43 kg
ENGLISH 19