Before Use; Fields Of Application - 3M 64396 Manual De Instrucciones

When unpacking, check that the unit is complete and shows no signs of transport or storage damage. Read all the information carefully. It contains important
advice about how to use the unit, safety, maintenance and care. Please keep these operating instructions in a safe and pass on to any subsequent owners.
We reserve the right to make design and equipment changes.
Paper fi lter bag. Part Number - 64422 for 25 L-tank BGIA Class M approved, 5 pcs. = 1 set
Paper fi lter bag. Part Number - 64423 for 50 L-tank BGIA Class M approved, 5 pcs. = 1 set
Filter cassettes. Part Number - 64420 Polyester material, BGIA Class M approved, 2 pcs.=1 set
Plastic emptying bag. Part Number - 64421 BGIA class M permitted, 5 pcs = 1 set
Y Adaptor to use two tools on one Dust Extraction Unit. Part Number - 64418
Rubber Sleeve Graduated. To allow the fi tment of diff erent hose diameters. Part Number - 64419
For more accessories please refer to our accessories list or contact us.
For wet and dry extraction.
Dust class M vacuum cleaners are suited to extraction of dry non-fl ammable dust non-fl ammable liquids,
wood dust and hazardous dust with Workplace Explosure Limits > 0.1 mg/m³.
Switch the unit ON/OFF with the switch
Operating Modes
The following functions and settings are available:
0 = Extraction unit >off <
I = Extraction unit >on<
A = Ready mode for ON/OFF automatic mode.
(Extraction unit is switched ON/OFF by the tool)
RA = Ready mode like "A" plus automatic fi lter cleaning.
The power socket b is available for connecting an electrical tool.
2
The sockets e and f are available for connecting an air power tool. Maximum working preasure 6,2 bar (90psi)
2 2
Select modes A or RA when using this equipment together with a 3M Random Orbital Sander (PN 64380, 64381, 64382, 64383, 64384, 64385, and 64386).
Warning! Electrical tools must be switched off during connection. The power socket is permanently supplied with voltage when the plug
is in the mains socket regardless of the switch setting. In switch setting "0" the power socket could still be used as an extension cable (e.g. for lights).
Connected load: Extraction unit and connected unit max. 16 A.
Switch d operation for Standard units, Models: 64396, 64397, 64398, 64404, 64405 & 64406
2
The extraction output can be variably adjusted using the rotating switch
Pre-selection switch d operation for units of the class "M", Models: 64400, 64401, 64402, 64408, 64409 & 64410
2
It is important to select the correct setting for switch
An alarm (horn and light) will indicate when the extraction rate is too low.
When using this equipment together with a 3M Random Orbital Sander (PN 64380, 64381, 64382, 64383, 64384, 64385, and 64386) set Switch
Remember to adjust the switch
2
The extraction openings of the tools are not standardised. There is an adapter available PN 64419 which can be used for the respective tool.
3M Instruction Manual
75-078_DustExtraction.indd 8 75-078_DustExtraction.indd 8

BEFORE USE

USE ORIGINAL ACCESSORIES

FIELDS OF APPLICATION

COMMISSIONING
a in the top section (or switch to automatic mode).
2 1
2
d according to the hose diameter being used. The extraction is not otherwise adjusted.
2
Hose diameter
35 mm
27 mm
21 mm
d setting according to the hose diameter on removal of the sander.
d.
Switch setting
6
70 m³/h
40 m³/h
20 m³/h
d to 21.
2
16.03.2010 10:47:43 16.03.2010 10:47:43