Residual Risk - Ryobi R18TB Traducción De Las Instrucciones Originales

Safety, performance, and dependability have been given
top priority in the design of your blower.
INTENDED USE
The blower is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
The product can be used for quick and easy clean up of
sawdust, debris, leaves and dirt.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
BLOWER SAFETY WARNINGS
■ Wear a face filter mask in dusty conditions to reduce
the risk of injury associated with the inhalation of dust.
■ Do not point the blower nozzle in the direction of people
or pets.
■ Never place objects inside the blower tubes.
■ Do not operate the product near open windows, etc.
■ Slightly dampen surfaces in dusty conditions.
■ Use the full blower nozzle extension so the air stream
can work close to the ground.
■ Do not place blower on top of or near loose debris.
Debris may be sucked into intake vent resulting in
possible damage to the product.
■ Do not operate the product with defective guard or
enclosure or shields.
■ Always be sure of the footing on slopes and to walk,
never run.
■ Do not touch moving hazardous parts before the
product is disconnected from the mains and the moving
hazardous parts have come to a complete stop.
■ Always wear substantial footwear and long trousers
while operating the product.
■ If the product is dropped, suffers heavy impact or
begins to vibrate abnormally, immediately stop the
product and inspect for damage or identify the cause of
the vibration. Any damage should be properly repaired
or replaced by an authorised service centre.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISK

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■ Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
■ Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
■ Injury from flying objects from the blow tube airflow.
KNOW YOUR PRODUCT
See page 55.
1. Lower tube
2. Speed selector
3. Trigger
4. Battery port
MAINTENANCE
WARNING
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.
■ When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt and carbon dust.
■ Do not, at any time, let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
■ Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
■ For greater safety and reliability, all repairs should be
performed by an authorised service centre.
LUBRICATION
All of the bearings in the product are lubricated with a
suffi cient amount of high grade lubricant for the life span of
the product under normal operating conditions. Therefore,
no further lubrication is required.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1