Technical Specifications - Velleman HQ Power VDPDMXC173 Manual Del Usuario

• PROGRAM:
Press PROGRAM button for more than one second to enter the PROGRAM mode, the matching indicator is lit.
Press PATTERN+ to select desired pattern, make a setting by means of fader 1 to 8 and press the program button
once to store the settings as a new step. Make a new setting and press program once again. If you have entered all
your steps press the SHIFT+END STEP button together to define the last step.
Example: make a setting on the 11th pattern to put channel 1~16 full on in a sequence.
1. Press program button for more than one second to enter program mode, the matching indicator is lit.
2. Press PATTERN+ or PATTERN- and STEP+ or STEP- till the LCD shows 11:01.
3. Slide fader 1 up to full and the other faders down to 0. Press latch 9-16 buttons to turn all matching indicator
off. After this setting press the program button once, now the LCD would show 11:02.
4. Slide fader 2 up to full, the other faders down to 0 and press the program button, now the LCD shows 11:03.
5. Continue this way until the LCD shows 11:09. Slide all faders to 0 and press LATCH9 to turn channel 9 indicator on.
Press the program button once and the LCD shows you 11:10.
6. Continue your setting till the LCD shows 11:17 and press the step-button to alert 11:17 to 11:16.
7. Press SHIFT + END STEP to define the 16th step to the last step. Now your pattern is complete.
• ASSIGN PROGRAM:
There are 16 ASSIGN for levels set by fader 1 to 8 and latch 9 to 16.
Example: assign 'ch.1 to 9 full on and ch.10 to 16 blackout' to "flash1" button.
1. Press assign button for more than one second to enter assign program mode, the matching indicator lights up.
2. Slide fader 1 to 8 to full and press latch 9 button to turn channel 9 indicator on.
3. Press assign button, then flash 1 button, all channel indicators flash three times. Now assign 1 is complete.
• PATCH SETTING:
In patch mode you could allocate easily the outgoing DMX channels to your light fixtures.
Example: To allocate 1-16 DMX channels, please proceed as follows.
1. Press patch button for more than one second to enter the patch mode. The matching indicator lights up. Press
STEP+ or STEP– till the right two digits on the LCD are "01" and press PATTERN+ or PATTERN– till the left
two digits are "16". Press PATCH briefly. Now DMX channel 1 is allocated to channel 16 of the device.
2. Press STEP+ and PATTERN- ; the LCD reads "15 02". Press PATCH briefly. Now DMX channel 2 is allocated
to channel 15 on the device.
3. Repeat step 2 until DMX channel 16 is allocated to channel 1 on the device. Press the PATCH button for more
than one second to leave the patch mode, the matching indicator is off.
• RUN PATTERN IN CROSS MODE:
In cross mode, the patterns are executed step by step by sliding the MASTER fader up and down.
In Chase mode, press SHIFT+CROSS SETUP, the CROSS ON indicator is on.
Slide the MASTER fader to top position, press cross button to enter cross mode, the A indicator lights up.
Press PATTERN + or PATTERN - till the LCD shows 11:01.
Turn the level knob to the maximum, now the A indicator is full on.
Slide the MASTER fader from the top to the bottom position, the next step in the pattern is executed and that
step is counted on the LCD (reads 11:02). Now indicator A is off and indicator B is full on.
5. Cleaning and Maintenance
1. The housing and the installation location should not be deformed, modified or tampered with.
2. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
3. Disconnect the device from the mains prior to maintenance activities.
4. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
5. There are no user-serviceable parts.

6. Technical Specifications

VDPDMXC173 - 5 - VELLEMAN