Rockford Fosgate Polaris PMX-P2 Operación Manual página 5

Source Unit Settings
To access the source unit's settings, press and hold
the MENU button until the options appear. Rotate the
encoder to scroll through the list of settings. Then press
the encoder button to select the setting you wish to
change. (BALANCE>FADER>AUDIO>VOLTAGE GAUGE>BT
PAIRING>BEEP>TUNER REGION>SOFTWARE>FACTORY
DEFAULT)
This source unit has a zero current draw when turned off. All of
your settings and presets will be saved along with your vehicles
battery during storage.
SOURCE
Press the SRC button to show the different source options (FM
TUNER>AM TUNER>USB>BLUETOOTH>PANDORA). Use the ro-
tary encoder or press the SRC button to scroll through sources.
If a source is GREYED out, that means it is not available. An ex-
ample would be Bluetooth is greyed out because the Bluetooth
mobile device is not connected yet.
Once the Bluetooth mobile device is connected, Bluetooth
source selection will be available. See BT Device Pairing for
connecting your mobile device.
BALANCE
Press the encoder button to access BALANCE adjustment
settings. Rotate the encoder button to set output BALANCE.
FADER
Press the encoder button to access FADER adjustment settings.
Rotate the encoder button to set output FADER.
AUDIO
To access the AUDIO settings, press the AUDIO option from the
MENU screen. Rotate the encoder to scroll through the list of
settings. Then press the encoder button to select the setting
you wish to change. (7 BAND EQ>CROSSOVER>PEQ>SOURCE
GAIN>INTERNAL AMPLIFIER)
7 BAND EQ
Press the encoder button to access the 7 BAND EQ settings.
Use the rotary encoder to scroll through the EQ settings. (FLAT
> ROCK > CLASSIC > ACOUSTIC > DANCE > ELECTRONIC > HIP-
HOP > CUSTOM) When setting up the CUSTOM EQ, press the
encoder button to set the first frequency. Once active, rotate
the encoder to adjust the frequency settings. Press encoder
button again to access the next frequency. Repeat until all EQ
settings are complete. Press the MENU button to exit and go
back up one level.
CROSSOVER
Press to access the CROSSOVER settings. Use the
rotary encoder to select the crossover zone options
(FRONT>REAR>SUB). Press the encoder to adjust the frequency
of the crossover (60Hz>80Hz>120Hz>APF). Press MENU to exit
and go back up one level.
PUNCH EQ
Press to access the PUNCH EQ settings. Use the rotary encoder
to adjust the gain output (0-12). Press MENU to exit and go back
up one level.
Punch EQ is an onboard equalizer with up to +18dB @ 45Hz
and/or up to +12dB boost at 12.5kHz
SOURCE GAIN
To adjust the level of device input gain, scroll
through the inputs (FM TUNER>AM TUNER>WB
TUNER>USB>BLUETOOTH>PANDORA) to the device you want
to adjust, press the encoder button to access the gain settings.
Rotate the encoder button to set the level of gain. (-3dB > -2dB
> -1dB > 0dB > +1dB > +2dB > +3dB)
INTERNAL AMPLIFIER
Press to access the INTERNAL AMPLIFIER options. Use the
rotary encoder to select options (ON>OFF). When using
an amplifier to power your speakers, select OFF. If you are
powering your speakers directly from the source unit, select the
INTERNAL AMPLIFIER to ON.
VOLTAGE GAUGE
To display the vehicle voltage, press the encoder button on the
VOLTAGE GAUGE option.
BT DEVICE PAIRING
Press the encoder button to access options (DISCOVERABLE >
DEVICE).
DISCOVERABLE
This is used to determine if the units Bluetooth is discoverable
or not. You can either select ENABLE (allows Bluetooth devices
to discover PMX-P2) or DISABLE (PMX-P2 is not able to be
discovered by Bluetooth devices). When ENABLE is selected,
the PMX-P2 is now ready for pairing to your Bluetooth mobile
device. Open the Bluetooth settings on your mobile device to
find your source unit labeled "ROCKFORD PMX" and select.
DEVICE
Selecting DEVICE by pressing the encoder button will allow you
to rename the source unit with up to 16 characters. This gives
you the ability to have a unique name for easy identification
during device pairing. Press the encoder button to select the
letter to be changed and rotate the knob to change the value.
Repeat process until desired name is reached.
BEEP
Press the encoder button to access the BEEP options. Rotate
the encoder button to turn system beep ON/ OFF.
TUNER REGION
To adjust, press the encoder button to access. Rotate
the encoder button to select the TUNER REGION of your
preference. (EUROPE > USA > RUSSIA > LATIN > ASIA > JAPAN >
MIDEAST > AUSTRALIA)
SOFTWARE
VERSION - Press the encoder button to display the current
firmware version of the unit.
5
Settings